7
Battery Replacement/Disposal
It is recommended that the unit be returned to Customer Service for
battery replacement. Contact toll-free (866) 584-5504.
This unit contains a maintenance-free, non-spillable, sealed lead-acid
battery. This battery is fully recyclable and should be accepted at any
location that accepts common automotive starter batteries. Examples of
places that accept these batteries are: county or municipal recycling
drop-off centers, scrap metal dealers and retailers who sell automotive
replacement lead acid starter batteries.
WARNINGS
Do not dispose of the battery in fire, as this may result in an explosion.
Before disposing of the battery, protect exposed terminals with
heavy-duty electrical tape to prevent shorting (shorting can result in
injury or fire).
Do not expose battery to fire or intense heat, as it may explode.
DC Plug Fuse Replacement
The fuse in the DC plug protects the charging circuit of the DC recharge adapter. If
the AC recharger operates but the DC charging adapter does not, then the fuse may
be opened.
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate replacement fuse with same type and rating.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Check for proper operation of DC charging adapter.
TROUBLESHOOTING
No Charge Indicator Light
If the Charge Indicator LED does not light during 120 Volt AC charging/recharging,
do the following:
1. Check for bad connection to the AC Recharge Port
2. Check for bad connection to the AC adapter
3. Confirm there is functioning AC or DC current
Note:
None of the Charge Indicator LEDs light during 12 Volt DC charging/recharging.
Operating Issues
1. When charging using the 120 volt AC method, the Spotlight will not operate.
The Area Light will turn on when pressed while charging. Be sure all adapters
are disconnected before Spotlight usage.
2. If the unit does not operate, the battery may be completely discharged. Charge
the unit using the AC adapter following the directions in the manual.
6
4. Slide the Air Compressor/OFF/Inflator Switch to INFLATOR (bottom position).
5. When product is fully deflated, turn the Air Compressor/OFF/Inflator Switch to
OFF, remove hose from valve and close the valve.
CARE AND MAINTENANCE
All batteries lose charge with time. AC recharge is recommended after each use or
every two months when not in frequent use. Use the AC recharger and charge for
the recommended time.
If the unit gets dirty, gently clean the outer surfaces of the Spotlight with a soft cloth
moistened with a mild solution of water and detergent. Periodically inspect the
condition of recharge adapters, connectors, and wires. Replace any components
that may have become worn or broken.
Replacement Parts
The quartz halogen bulb and sealed lead acid batteries are available through Vector
Manufacturing. A comparable (12 volt H3, 25 watt) bulb may be substituted. These
can also be purchased from popular automotive parts suppliers nationwide. Contact
Vector Manufacturing’s Technical Support Department for replacement parts
(including replacement adapters and cords) and any additional information that you
may need. They may be reached at (954) 584-4446 or toll free at (866) 584-5504.
WARNING
To reduce the risk of shocks or burns and avoid damage to the unit,
make sure all power switches are in the OFF position, all adapters are
unplugged and the unit has been allowed to cool down before
performing any maintenance/parts replacement.
Bulb Replacement
1. Remove the rubber bezel on the rim of the Spotlight to reveal eight small Phillips
screws in the retaining ring.
2. Using a screwdriver, remove (counterclockwise) the screws and set them aside.
3. Lift off the retaining ring, glass lens and rubber “O” ring and set them aside.
4. Carefully remove the reflector and bulb assembly.
5. Disconnect the bulb from the guarding wires and replace the burned out bulb
with one of the same type listed in the Specifications section of this manual.
6. Reassemble the guarding wires, put back the reflector, rubber “O” ring and
the lens.
7. Replace rubber bezel by sliding forward to the front of the spotlight.
8. Turn one of the spotlight’s ON/OFF switches to the ON position to ensure
proper operation of spotlight.
VEC280POB_Manual_071105 7/28/05 10:43 AM Page 6
