background image

 

 

POWERKING                                                    1-800-344-3371                              [email protected] 

Protecting Yourself and Those Around You 

 

This is a high-powered machine, with moving parts operating with a high amount of 
energy. You must operate the machine safely. Unsafe operation can create a number of 
hazards for you as well as anyone else in the vicinity. Always take the following 
precautions when using this machine: 

 

Keep in mind that the operator is responsible for accidents or hazards occurring 
to other people, their property, and themselves 

 

Always wear protective goggle / safety glasses with side shields while using the 
chipper to protect your eyes from debris 

 

Avoid wearing loose clothing or jewelry, which can catch on moving parts 

 

We recommend wearing gloves. Be sure your gloves fit properly and do not have 
loose cuffs or drawstrings 

 

Wear steel toed boots with non-slip treads. Do not use machine while barefoot or 
with open toed sandals 

 

Wear long pants / jeans 

 

Keep bystanders at least 50 feet away from your work area at all times. Stop the 
engine when another person or pet approaches.  

 

Safety for Children and Pets 

 

Tragic accidents can occur if the operator is not alert to the presence of children and 
pets. Children are often attracted to the machine and the operation of the unit. Never 
assume that children will remain where you last saw them. Always follow these 
precautions. 

 

Keep children and pets at least 50 feet from the working area and ensure they 
are under the watchful care of a responsible adult.  

 

Be alert and turn the machine off if children or pets enter the work area. 

 

Never allow children to operate the chipper. 

Summary of Contents for PK0915-EH
















Reviews: