OPERATION
Always observe the safety instructions and applica-
ble regulations.
Firmly hold the machine and push the bit with even pres-
sure into the workpiece. Do not force the machine.
Use only bits that do not yet show any signs of wear.
Worn bits have a negative effect on the efficiency of the
machine.
TORQUE ADJUSTMENT
Fig. E
The machine has different torque settings by means of
which the force for fastening and loosening screws can
be determined.
•
Put the torque setting ring (2) at the required torque.
•
Preferably select the lowest possible setting to move
the screw. Select a higher torque setting when the
motor is slipping.
•
If the battery gets discharged, the motor will not slip
in position 4 or 5. Recharge the battery.
FASTENING AND LOOSENING SCREWS.
•
Push the top half of the direction switch (Fig. A. 3)
down to fasten screws.
•
Push the lower half of the direction switch (Fig. A. 3)
up to loosen screws.
BLOCKING THE DIRECTION SWITCH.
After use block the direction switch by pressing the lock
to the left into the lock position. This action prevents
unwanted operation of the machine.
CHARGING BATTERIES
THE BATTERY THAT COMES WITH THE MACHINE IS
NOT FULLY CHARGED.
•
Only use the battery charger at temperatures between
+10 and +40 °Celsius.
•
Only use the battery charger in dry rooms.
CHARGING
•
Unlock the accu lock and remove the battery from
the machine.
•
Push the adapter plug of the mains adapter into the
connector situated in the side of the charger.
•
Plug the mains adapter into the (wall) socket.
•
If the battery is completely discharged or not used for
a long period, it takes about 24 hours to charge the
battery. Normally it takes about 5 hours.
•
Place the battery in the tool after charging.
6
Powercraft
CORDLESS SCREWDRIVER
THE NUMBERS IN THE FOLLOWING TEXT COR-
RESPOND WITH THE PICTURES AT PAGE 2.
TECHNICAL SPECIFICATIONS
PRODUCT INFORMATION
Fig. A + B.
1 Hexagonal drive shaft
2 Torque setting ring
3 Direction switch
4 Lock
5 Battery release button
6 Battery
PACKAGE CONTENTS
1 Cordless screwdriver
1 Charging adaptor
5 Slotted bits
4 Philips bits
4 Pozidrive bits
7 Torque bits
6 Hexagonal bits
2 Square bits
8 Sockets 5 - 12 mm
1 Adaptor
1 Adaptor Hex to Socket
1 Instruction manual
1 Guarantee
card
Check the machine, loose parts and accessories for
transport damage.
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
Electrical safety
Check that your mains voltage corresponds to the
input voltage of the charging adapter.
The charging adapter is double insulated in
accordance with EN-60335; therefore no
earth wire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
GENERAL SAFETY INSTRUCTIONS
1. Keep work area clean.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Don’t expose power tools to rain. Don’t use power
tools in damp or wet locations. Keep work area well
lit. Don’t use power tools in presence of flammable
liquids or gases.
3. Guard against electric shock.
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges refrigerators).
4. Keep children away.
Do not let visitors contact tool or extension cord. All
visitors should be kept away from work area.
5. Store idle tools.
When not is use, tools should be stored in dry,
high, or locked-up place, out of reach of children.
6. Don’t force tool.
It will do the job better and safer at the rate for
which it was intended.
7. Use right tool.
Don’t force small tools or attachments to do the job
of heavy duty tool.
8. Dress properly.
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and nonskid
footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
9. Use safety glasses.
Also use face or dust mask if operation is dusty.
10. Don’t abuse cord.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
Voltage
| 4.8
V —
---
Voltage charging adaptor
| 230 V~
Frequency
| 50 Hz
Capacity battery
| 600 mAh
Charging time
| 5 hours
Number of torque
| 6
Speed. No load
| 150/min
Weight (incl. battery)
| 0,4 kg
Weight charging adaptor
| 0,3 kg
Total length
| 239 mm
UK
English
Powercraft
3
