Powercraft
13
•
The ventilating apertures (3) on the housing must remain clear to ensure optimum cooling
of the motor.
•
Push the on/off switch (1) to start the machine.
•
Move the sander over the surface of your workpiece.
•
Push the on/off switch to stop the machine.
Prevent pushing too much on the machine during sanding. Excessive sanding
pressure does not lead to increased sanding capacity, but increases wear of the
machine and the sandpaper.
User tips
•
Apply long uniform movements to your sander to obtain the best possible results.
•
The surface quality after sanding is determined by the selected grain.
Product information
Fig. C
1. On/off
trigger
2.
Trigger locking button
3. Jigsaw
blade
4. Bottom
plate
5. Guard
6.
Allen key
7.
Saw buckle
8.
Angle adjustment
Special safety instructions
1.
Check the following points:
•
Has the saw lost any teeth and is it showing cracks or fractures?
•
If so, replace the saw immediately.
•
Is there enough room under the workpiece so that the saw does not come into contact
with the floor or work table as it moves up and down?
•
Do the teeth of the saw point upwards?
2.
Always wear protective goggles when using the appliance.
3.
Maintain the appliance carefully.
4.
Do not use the appliance in a wet environment.
5.
Do not use the appliance for material which contains asbestos.
6.
Never leave the jigsaw unattended.
Using the appliance
1.
Clamp the workpiece that you will be sawing in firmly into place.
2.
Remove any wood residue that is near the saw or stuck to the surface of the saw; do not
use your hand for this. Switch the appliance off before removing any residue!
3.
Always switch the jigsaw on in idle, i.e. switch the saw on before bringing it into contact
with the workpiece.
4.
When sawing the wood watch out for knots, nails, cracks and/or dirt deposits.
5. JIG SAW
08
Powercraft
g. If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of these devices can reduce dust
related hazards.
h.
Use clamps or a vice to hold work. It’s safer than using your hand and it frees both hands to
operate tool.
4)
Power tool use and care
a.
Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c.
Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc., in accordance with these instructions
and in the manner intended for the particular type of power tool, taking into account the
working conditions and the work to be performed. Use of the power tool for operations
different from intended could result in hazardous situation.
h.
Damaged switches must be replaced at a customer service repair centre. Do not use
power tools that cannot be switched on and off.
i.
Do not leave power tools unattended while they are switched on. Always switch off the
tool and wait until it has come to a full standstill before leaving.
j.
If the mains cable has been damaged, it must be replaced with a special mains cable.
These can be obtained from the manufacturer or the manufacturer's customer service
department. The mains cable may only be replaced by the manufacturer, the
manufacturer's customer service department or equally qualified persons.
5)
Battery tool use and care
a.
Ensure the switch is in the off position before inserting battery pack. Inserting the battery
pack into power tools that have the switch on invites accidents.
b.
Recharge only with the charger specified by the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of fire when used with another battery pack.
c.
Use power tools only with specifically designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
d.
When battery pack is not in use, keep it away from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal objects that can make a connection from
one terminal to another. Shorting the battery terminals together may cause burns of a fire.
e.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritations or burns.
GB
GB