Poulan Pro PR450N20S Operator'S Manual Download Page 18

18

TO CHANGE ENGINE OIL
(SEE ENGINE MANUAL)

•  Be sure lawn mower is on level surface.
•  Oil will drain more freely when warm.
•  Catch oil in a suitable container.
•  For engines without dipstick, re move 

bottom oil drain plug.

•  For engines with oil fill cap/dipstick, 

remove bottom drain plug or remove 
engine oil cap and turn lawn mower on 
its side.

NOTE

:  Before tipping lawn mower to 

drain oil, empty fuel tank by running en-
gine until fuel tank is empty.
•  After oil has drained completely, re place 

oil drain plug and tighten se cure ly.

•  Refill engine with oil.  Pour slowly.  Do 

not overfill.

•  Fill to top of slot inside of filler hole or 

to “FULL” line on dipstick on models so 
equipped.  Keep oil at proper level.

AIR FILTER

Your engine will not run properly and may 
be damaged by using a dirty air filter. 
Clean the element after every 25 hours 
of operation or every season.  Replace 
the air filter every 100 hours of operation 
or every season, whichever occurs first.  
Service air cleaner more often under dusty 
conditions.  See the maintenance section 
of your engine manual.

MUFFLER

Inspect and replace corroded muffler as it 
could create a fire hazard and/or damage.

IN-LINE FUEL FILTER (KOHLER or B&S 
PRO / ENDURANCE ENGINES ONLY)

The fuel filter should be replaced once 
each season.  If fuel filter becomes 
clogged, ob struct ing fuel flow to car bu re-
 tor, re place ment is re quired.
1.  With engine cool, remove filter and 

plug fuel line sec tions.

2.  Place new fuel filter in position in fuel 

line with arrow pointing towards carbu-
retor.

3.  Be sure there are no fuel line leaks and 

clamps are properly positioned.

4.  Immediately wipe up any spilled gaso-

line.

SPARK PLUG

Replace spark plug at the beginning of 
each mowing season or after every 100 
hours of operation, whichever occurs first.  
Set spark plug gap according to engine 
manual specifications.

CLEANING

IMPORTANT:

  For best performance, keep 

mower housing free of grass build-up and 
trash. Clean the underside of your mower 
after each use.
•  Clean the underside of your lawn mower 

by scraping to remove buildup of grass 
and trash.

•  Clean engine often to keep trash from 

accumulating.  A clogged engine runs 
hotter and shortens engine life. 

•  Keep finished surfaces and wheels free 

of all gasoline, oil, etc.

•  With the exception of the water washout 

port (if equipped), we do not recom-
mend using a garden hose to clean the 
outside of your lawn mower unless the 
elec tri cal system, muffler, air filter and 
carburetor are covered to keep water 
out.  Water in engine can result in short-
ened engine life.

GRASS CATCHER (IF SO EQUIPPED)

Grass catcher may be hosed with water 
but must be dry when used.

 

CAUTION:

  Under nor mal usage, the 

catch er material is subject to de te ri o ra tion 
and wear and should therefore be 
checked to ensure compliance with 
origi nal manufacturer specifications.

Fuel 
Filter

Clamp

Clamp

MAINTENANCE

Summary of Contents for PR450N20S

























Reviews: