background image

24

Fig. 35

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 35)

WARNING:  Do not short battery 

ter mi nals by allowing a wrench or any 

other object to contact both terminals 

at the same time. Before connecting 

battery, remove metal bracelets, 

wristwatch bands, rings, etc. Positive 

terminal must be connected first to 

prevent sparking from ac ci den tal 

grounding.

•  Lift seat pan to raised position.
• 

Disconnect BLACK battery cable first then RED battery 

cable and carefully remove battery from tractor.

•  Install new battery with terminals in same position as 

old battery.

• 

First connect RED battery cable to positive (+) terminal 

with bolt and nut as shown. Tighten securely. Slide 

terminal cover over terminal.

•  Connect BLACK grounding cable to negative (-) ter-

 mi nal with remaining bolt and nut. Tighten se cure ly.

•  Lower seat pan.

02603

SEAT PAN

NUT

POSITIVE 

(RED) 

CABLE

NEGATIVE 

(BLACK) 

CABLE

BOLT

TERMINAL 

COVER

ENGINE

TO AD JUST THROTTLE CON TROL CABLE 

The throttle control has been preset at the factory and 

ad just ment should not be necessary. If adjustment is nec-

 es sary, see engine manual.

TO AD JUST CHOKE CON TROL 

The choke control has been preset at the factory and ad just-

 ment should not be necessary. If adjustment is necessary, 

see engine manual.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run 

poorly, stop running, or prevent it from starting.
• Check 

wiring.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse.  The 

fuse holder is located behind the dash.

Fig. 36

03078

HOOD

HEADLIGHT

WIRE

CONNECTOR

TO REMOVE HOOD AND GRILL ASSEMBLY 

(See Fig. 36)

• Raise 

hood.

•  Unsnap headlight wire connector.
• 

Stand in front of tractor.  Grasp hood at sides, tilt toward 

engine and lift off of tractor.

•  To replace, reverse above procedure.

Summary of Contents for PP17G42

























































Reviews: