background image

24

0066

3sq

RE TAIN ING 
RING

WASH ERS

FIG. 28

AXLE 
COVER

TO REMOVE WHEEL FOR REPAIRS 

FRONT WHEEL (See Fig. 28)
•      Block up axle securely.
•         Remove axle cover, retaining ring and washers to allow 

wheel removal.

•      Repair tire and reassemble.
•      Replace washers and snap retaining ring securely in 

axle groove.

•      Replace axle cover.

REAR WHEEL -
•      Block rear axle securely.
•      Remove fi ve (5) hub bolts to allow wheel removal.
•      Repair tire and reassemble.  Replace and tighten hub 

bolts securely.

NOTE: 

To seal tire punctures and prevent fl at tires due to 

slow leaks, tire sealant may be purchased from your local 
parts dealer. Tire sealant also prevents tire dry rot and 
corrosion.

SERVICE AND ADJUSTMENTS

02614

WEAK OR DEAD
BATTERY

FULLY CHARGED
BATTERY

FIG. 29

TO START ENGINE WITH A WEAK BAT TERY 
(See Fig. 29) 

WARNING

:

  Lead-acid batteries gen-

 er ate ex plo sive gases.  Keep sparks, 
fl ame and smoking ma te ri als away from 
bat ter ies.  Always wear eye pro tec tion 
when around batteries.

If your battery is too weak to start the engine, it should be 
recharged. (See "BATTERY" in the Maintenance sec tion 
of this man u al).

If “jumper ca bles” are used for emer gen cy starting, follow 
this pro ce dure:

IMPORTANT

:  YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT 

SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT 
SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START 
OTHER VEHICLES. 

TO ATTACH JUMPER CABLES -
•      Connect one end of the RED cable to the POSITIVE 

(+) terminal of each battery(A-B), taking care not to 
short against tractor chassis.

•         Connect one end of the BLACK ca ble to the NEGA TIVE 

(-) terminal (C) of fully charged battery.

•      Connect the other end of the BLACK cable (D) to good 

chassis ground,  away from fuel tank and bat tery.

TO REMOVE CABLES, REVERSE ORDER -
•      BLACK cable fi rst from chassis and then from the fully 

charged battery.

•      RED cable last from both batteries.

TO AD 

JUST STEER 

ING WHEEL  ALIGN-

 MENT

If steering wheel crossbars are not horizontal (left to right) 
when wheels are positioned straight forward, remove steer-
 ing wheel and reassemble per instructions in the Assembly 
section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on 
your tractor.  If damage has occurred to affect the front 
wheel toe-in or camber, contact your nearest authorized 
service center/department. 

Summary of Contents for PKGTH2554

































Reviews: