background image

21

KEY   PART 

NO.    NO. 

DESCRIPTION

 4  191079 

 Pulley, Impeller

  5  188909 

 Bearing Assembly, Flange

  6  155377 

 Nut, Hex Flange  5/16-18

  7  180355 

 Bolt, Flat Head, Carriage

     

 5/16-18 x 5/8

  8  72270505 

 Bolt, Carriage  5/16-18

  9  163183 

 Bolt, Hex Head

 10  404930X428   Housing, Auger

 11  404933X428   Bar, Scraper

 12  178675X008   Bracket, Corner Discharge

 13  175322 

 Base, Discharge Chute

 14  10040500 

 Washer, Lock  5/16

 15  19111507 

 Washer, Flat

 16  74940516 

 Screw, Hex Head  5/16-18 x 3/4

 17  405637 

 Grease Fitting

 18  179582 

 Screw, Hex Head  5/16 x 1

 19  73800400 

 Nut, Hex Lock  1/4-20

 20  155377 

 Nut, Hex Lock  5/16-18

 22  178777X479   Skid Plate, RH

 25  72270506 

 Bolt, Carriage  5/16-18 x 3/4

 26  174658 

 Bearing, Auger

 27  174697 

 Washer, Thrust, 1"

 28  198636 

 Bolt, Shear

 29  174762X479   Skid Plate, LH

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP10530ES

  (96192001800)

AUGER HOUSING / IMPELLER ASSEMBLY

NOTE:

  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:

  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

KEY   PART 

NO.    NO. 

DESCRIPTION

 30  405973X479   Auger Assembly, RH

 31  405972X479   Auger Assembly, LH

 32  407768 

 O-Ring

 33  407769 

 Bushing, Flange  3/4

 34  174681 

 Washer, Thrust  3/4

 35  174684 

 Bearing, Thrust  3/4

 36  407757 

 Shaft, Impeller

 37  174683 

 Washer, Thrust  5/8

 38  407758 

 Bushing, Flange  5/8

 39  407767 

 Screw, Hex Head  5/16-18 x 3/4

 40  407760 

 Plug, Case

 41  407761 

 Housing, Gearbox, RH

 42  407770 

 Seal, Oil

 43  407762 

 Bushing, Flange, 1"

 44  189282 

 Key, Square  1/4 x 1/4 x 7/8

 45  407763 

 Gear, Worm

 46  407764 

 Shaft, Auger

 47  407765 

 Housing, Gearbox, LH

 48  175321X479   Impeller Assembly

 49  74780426 

 Screw, Hex Head  1/4-20 x 1-5/8

 50  407766 

 Gasket, Gearbox

 51  7836M 

 Pin, Roll  3/16 x 1-1/8

 55  198638 

 Spacer

 56  180684 

 Multi-Wrench

 57  196710 

 Gearbox Assembly

 58  411939 

 Plug, Bearing, Hole, HSG

Summary of Contents for 96192001800

































Reviews: