background image

19

WARRANTY COMMENCEMENT DATE:

The warranty period begins on the date the

small off--road engine is purchased.

LENGTH

OF COVERAGE:

This warranty shall be for a

period of two years from the initial date of pur-

chase.

WHAT IS COVERED: REPAIR OR

REPLACEMENT OF PARTS.

Repair or re-

placement of any warranted part will be per-

formed at no charge to the owner at an ap-

proved ELECTROLUX HOME PRODUCTS,

INC., servicing center. If you have any ques-

tions regarding your warranty rights and re-

sponsibilities, you should contact your nearest

authorized service center or call ELECTRO-

LUX

HOME

PRODUCTS,

INC.,

at

1--800--554--6723.

WARRANTY PERIOD:

Any warranted part which is not scheduled for

replacement as required maintenance, or

which is scheduled only for regular inspection

to the effect of “repair or replace as necessary”

shall be warranted for 2 years. Any warranted

part which is scheduled for replacement as re-

quired maintenance shall be warranted for the

period of time up to the first scheduled replace-

ment point for that part.

DIAGNOSIS:

The

owner shall not be charged for diagnostic labor

which leads to the determination that a war-

ranted part is defective if the diagnostic work is

performed at an approved ELECTROLUX

HOME PRODUCTS, INC., servicing center.

CONSEQUENTIAL DAMAGES:

ELECTRO-

LUX HOME PRODUCTS, INC., may be liable

for damages to other engine components

caused by the failure of a warranted part still

under warranty.

WHAT IS NOT COVERED

: All failures caused

by abuse, neglect, or improper maintenance

are not covered.

ADD--ON OR MODIFIED

PARTS:

The use of add--on or modified parts

can be grounds for disallowing a warranty

claim. ELECTROLUX HOME PRODUCTS,

INC., is not liable to cover failures of warranted

parts caused by the use of add--on or modified

parts.

HOW TO FILE A CLAIM:

If you have

any questions regarding your warranty rights

and responsibilities, you should contact your

nearest authorized service center or call

ELECTROLUX HOME PRODUCTS, INC., at

1--800--554--6723.

WHERE TO GET WAR-

RANTY SERVICE:

Warranty services or re-

pairs shall be provided at all ELECTROLUX

HOME PRODUCTS, INC., service centers.

Call: 1--800--554--6723

MAINTENANCE, RE-

PLACEMENT AND REPAIR OF EMISSION

RELATED PARTS

: Any ELECTROLUX

HOME PRODUCTS, INC., approved replace-

ment part used in the performance of any war-

ranty maintenance or repair on emission re-

lated parts will be provided without charge to

the owner if the part is under warranty.

EMIS-

SION CONTROL WARRANTY PARTS LIST:

Carburetor, Ignition System: Spark Plug (cov-

ered up to maintenance schedule), Ignition

Module, Muffler including catalyst.

MAINTE-

NANCE STATEMENT:

The owner is responsi-

ble for the performance of all required mainte-

nance as defined in the instruction manual.

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

Summary of Contents for 545001498




















Reviews: