Poulan Pro 437921 Page 26 Owner'S Manual Download | Manualshive

Page: 26 / 40

background image

26

NOTE:

All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT:

Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

KEY PART

NO. NO.

DESCRIPTION

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003602)
CONTROL PANEL / CHUTE

1

2

2

*3

*4

*5

*6

*7

01.09.010-B

1

428272

LEVER/CABLE ROTATOR ASSEMBLY

2

17501010

SCREW 10-24 X .625

*3 420678 ROTATOR

HEAD

*4

405932

ROTATOR PIVOT BRACKET

*5 420675 PULLEY

PIVOT

*6

428273

CABLE ASSEMBLY ADJUSTABLE

*7

428310

CABLE ASSEMBLY HEAT SHIELD

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

«
...
24
25
26
27
28
...
»

Summary of Contents for 437921









































Reviews:

No comments

Related manuals for 437921

Brand: EINHELL Pages: 60

Brand: Deltafox Pages: 116

Brand: Senix Pages: 20

Brand: Kobalt Pages: 24

Brand: hecht Pages: 44

Brand: AP&T Pages: 4

Brand: Eckman Pages: 13

Brand: Worx Pages: 24

Brand: Toro Pages: 20

Brand: Toro Pages: 30

Brand: Farm King Pages: 76

Brand: Snapper Pages: 28

Brand: Snapper Pages: 32

Brand: Snapper Pages: 36

Brand: Ewbank Pages: 12

Brand: Ewbank Pages: 12

Brand: Troy-Bilt Pages: 72

Brand: McCulloch Pages: 312

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands