background image

21

REPAIR PARTS

  SNOW THROWER - - MODEL NO. 

PR8527ES 

(96192001702)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY   PART 

NO.    NO. 

DESCRIPTION

 4  191079 

 Pulley, Impeller

  5  188909 

 Bearing Assembly, Flange

  6  155377 

 Nut, Hex Flange  5/16-18

  7  180355 

 Bolt, Flat Head, Carriage  5/16-18 x 5/8

  8  72270505 

 Bolt, Carriage  5/16-18 x 5/8

  9  163183 

 Nut, Cage  3/8-16

 10  404929X428   Housing, Auger

 11 

404932X479

  

Bar, Scraper

 12  178675X008   Bracket, Corner Discharge

 13  175322 

 Base, Discharge Chute

 14  10040500 

 Washer, Lock  5/16

 15  19111507 

 Washer, Flat

 16  74940516 

 Screw, Hex Head  5/16-18 x 3/4

 17  405637 

 Grease Fitting

 18  179582 

 Screw, Hex Head  5/16 x 1

 19  73800400 

 Nut, Hex Lock  1/4-20

 20  155377 

 Nut, Hex Lock  5/16-18

 22  178777X479   Skid Plate, RH

 25  72270506 

 Bolt, Carriage  5/16-18 x 3/4

 26  174658 

 Bearing, Auger

 27  174697 

 Washer, Thrust, 1"

 28  198636 

 Bolt, Shear

 29  174762X479   Skid Plate, LH

 30 

413607X479

   Auger Assembly, RH

 31 

413606X479

   Auger Assembly, LH

 32  407768 

 O-Ring

 33  407769 

 Bushing, Flange  3/4

 34  174681 

 Washer, Thrust  3/4

 35  174684 

 Bearing, Thrust  3/4

 36  407757 

 Shaft, Impeller

 37  174683 

 Washer, Thrust  5/8

 38  407758 

 Bushing, Flange  5/8

 39  407767 

 Screw, Hex Washer Head  5/16-18 x 3/4

 40  407760 

 Plug, Case

 41  407761 

 Housing, Gearbox, RH

 42  407770 

 Seal, Oil

 43  407762 

 Bushing, Flange, 1"

 44  189282 

 Key, Square  1/4 x 1/4 x 7/8

 45  407763 

 Gear, Worm

 46  407764 

 Shaft, Auger

 47  407765 

 Housing, Gearbox, LH

 48  175321X479   Impeller Assembly

 49  74780426 

 Screw, Hex Head  1/4-20 x 1-5/8

 50  407766 

 Gasket, Gearbox

 51  7836M 

 Pin, Roll  3/16 x 1-1/8

 55  198638 

 Spacer

 56  180684 

 Multi-Wrench

 57  196710 

 Gearbox Assembly

 58  411939 

 Plug Bearing Hole

NOTE:

  All component dimensions given in U.S. inches.    1 inch = 25.4 mm

IMPORTANT:

 Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Summary of Contents for 416810

































Reviews: