background image

15

CARBURETOR ADJUSTMENTS

Your carburetor is equipped with limiter caps.

Carburetor adjustment is a complicated task.

We recommend that you take your unit to an

authorized service dealer. Damage will occur if

you turn the needles beyond the limiter stops.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut, or been run with an improper

amount of bar lubrication it may be necessary

to service your bar. A worn bar will damage

your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in

the STOP position, then clean all sawdust from

the guide bar and sprocket hole.

To maintain guide bar:

S

Move ON/STOP switch to the STOP posi-

tion.

S

Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

S

Clean the oil holes and bar groove after each

5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Sprocket Hole

Oil Holes

S

Add lubricant to sprocket hole after each

use.

S

Burring of guide bar rails is a normal process

of rail wear. Remove these burrs with a flat

file.

S

When rail top is uneven, use a flat file to re-

store square edges and sides.

Correct Groove

Worn Groove

File Rail Edges

and Sides

Square

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when exce-

ss heating or burring of the rails occurs. If re-

placement is necessary, use only the guide bar

specified for your saw in the repair parts list or

on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that

requires special tools. We recommended

you refer chain sharpening to a professional

chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better.

S

Loosen 3 screws on cylinder cover.

S

Remove the cylinder cover.

S

Pull off the spark plug boot.

S

Remove spark plug from cylinder and dis-

card.

S

Replace with Champion RCJ--7Y spark

plug and tighten securely with a 3/4 inch

socket wrench. Spark plug gap should be

0.025 inches.

S

Reinstall the spark plug boot.

S

Reinstall the cylinder cover and 3 screws.

TIghten securely.
Screws

Spark

Plug Boot

Spark

Plug

Cylinder

Cover

STORAGE

WARNING:

Stop engine and allow

to cool, and secure the unit before storing or

transporting in a vehicle. Store unit and fuel

in an area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

Store unit with all guards in place. Position so

that any sharp object cannot accidentally

cause injury to passersby. Store the unit out

of reach of children.

S

Before storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

S

Clean the unit before storing. Pay particu-

lar attention to the air intake area, keeping

it free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

S

Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

S

Store in a dry area out of the reach of chil-

dren.

CAUTION:

It is important to prevent gum

deposits from forming in essential fuel system

parts such as the carburetor, fuel filter, fuel

hose, or fuel tank during storage. Alcohol

blended fuels (called gasohol or using ethanol

or methanol) can attract moisture which leads

to fuel mixture separation and formation of

acids during storage. Acidic gas can damage

the engine.

NEED ASSISTANCE?

NEED ASSISTANCE?

Call 1--800--554--6723.

NEED SERVICE PART?

Contact your authorized service dealer.

Summary of Contents for 2001-08



















Reviews: