Poulan Pro 191491 Owner'S Manual Download Page 13

Page: 13 / 33

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of
various controls and ad just ments. Save this manual for future reference.

Our tractors conform to the safety standards of the

American National Stan dards Institute.

ATTACHMENT CLUTCH SWITCH

Used

to engage the mower blades, or other at-
tachments mounted to your trac tor.

LIGHT SWITCH

POSITION

- Turns the

head lights on and off.

THROTTLE CONTROL

Used to con trol

engine speed.

BRAKE PEDAL

- Used for braking the

tractor and starting the engine.

CHOKE CONTROL

- Used when start ing

a cold engine.

HEIGHT ADJUSTMENT KNOB

- Used to

adjust the mow er cutting height.

IGNITION SWITCH

- Used for starting and

stopping the engine.

ATTACHMENT LIFT LEVER

- Used to raise

and lower the mower deck or other at tach ments
mounted to your tractor.

LIFT LEVER PLUNGER

- Used to re lease

attachment lift lever when chang ing its
position.

AMMETER

- Indicates charging (

) or

discharging (

) of battery.

PARKING BRAKE LEVER

- Locks brake

pedal into the brake po si tion.

MOTION CONTROL LEVER

- Selects the

speed and direction of tractor.

FREEWHEEL CONTROL

- Disengages

transmission for pushing or slowly towing
the tractor with the engine off.

MOTION DRIVE BELT TENSION HAN-
DLE

- Used when changing motion drive

belt and, if necessary, starting engine
under extremely cold conditions.

02507

Light Switch
Position

Lift
Lever
Plunger

Attachment
Lift Lever

Parking Brake
Lever

Motion Control
Lever

Height
Adjustment
Knob

Ignition
Switch

Attachment
Clutch Switch

Ammeter

Choke
Control

Throttle
Control

Brake Pedal

Free Wheel
Control

Approx.
Speed:
3MPH
2MPH
1MPH

Motion Drive
Belt Tension
Handle

Summary of Contents for 191491


































Search results

Summary of Contents for 191491

Reviews:

Related manuals for 191491

Brands by name

Popular brands

Poulan Pro 191491, Owner'S Manual

Search results

Summary of Contents for 191491

Reviews:

Related manuals for 191491

Brands by name

Popular brands