Poulan Pro 178379 Owner'S Manual Download Page 2

2

I. GENERAL OPERATION

Read, understand, and follow all instructions in the manual
and on the machine before starting.

Only allow responsible adults, who are familiar with the
instructions, to operate the machine.

Clear the area of objects such as  rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.

Be sure the area is clear of other people before mowing.
Stop machine if anyone enters the area.

Never carry passengers.

Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.

Be aware of the mower discharge direction and do not point
it at anyone.  Do not operate the mower without either the
entire grass catcher or the guard in place.

Slow down before turning.

Never leave a running machine unattended.  Always turn
off blades, set parking brake, stop engine, and remove
keys before dismounting.

Turn off blades when not mowing.

Stop engine before removing grass catcher or unclogging
chute.

Mow only in daylight or good artificial light.

Do not operate the machine while under the influence of
alcohol or drugs.

Watch for traffic when operating near or crossing road-
ways.

Use extra care when loading or unloading the machine into
a trailer or truck.

Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related
injuries.  These operators should evaluate their ability to
operate the riding mower safely enough to protect them-
selves and others from serious injury.

Keep machine free of grass , leaves or other debris build-
up which can touch hot exhaust / engine parts and burn.
Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur. Clean
any oil or fuel spillage before operating or storing the
machine. Allow machine to cool before
storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tipover
accidents, which can result in severe injury or death.  All slopes
require extra caution.  If you cannot back up the slope or if you feel
uneasy on it, do not mow it.

DO:

Mow up and down slopes, not across.

Remove obstacles such as rocks, tree limbs, etc.

Watch for holes, ruts, or bumps.  Uneven terrain could
overturn the machine.  

Tall grass can hide obstacles.

Use slow speed.  Choose a low gear so that you will not
have to stop or shift while on the slope.

Follow the manufacturer’s recommendations for wheel
weights or counterweights to improve stability.

Use extra care with grass catchers or other attachments.
These can change the stability of the machine.

Keep all movement on the slopes 

slow and gradual.  Do

not make sudden changes in speed or direction.

Avoid starting or stopping on a slope.  If tires lose traction,
disengage the blades and proceed slowly 

straight down

the slope.

Safe Operation Practices for Ride-On Mowers

IMPORTANT: 

 THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS.

FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

SAFETY RULES

DO  NOT:

Do not  turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.

Do not mow near drop-offs, ditches, or embankments.
The mower could suddenly turn over if a wheel is over the
edge of a cliff or ditch, or if an edge caves in.

Do not mow on wet grass. Reduced traction could cause
sliding.

Do not  try to stabilize the machine by putting your foot on
the ground.

Do not use grass catcher on steep slopes.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the
presence of children.  Children are often attracted to the
machine and the mowing activity.  

Never assume that children

will remain where you last saw them.

Keep children out of the mowing area and under the
watchful care of another responsible adult.

Be alert and turn machine off if children enter the area.

Before and when backing, look behind and 

down for small

children.

Never carry children.  They may fall off and be seriously
injured or interfere with safe machine operation.

Never allow children to operate the machine.

Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.

IV. SERVICE

Use extra care in handling gasoline and other fuels.  They
are flammable and vapors are explosive.
- Use only an approved container.
- Never remove gas cap or add fuel with the engine

running.  Allow engine to cool before refueling.  Do not
smoke.

- Never refuel the machine indoors.
- Never store the machine or fuel container inside where

there is an open flame, such as a water heater.

Never run a machine inside a closed area.

Keep nuts and bolts, especially blade attachment bolts,
tight and keep equipment in good condition.

Never tamper with safety devices.  Check their proper
operation regularly.

Keep machine free of grass, leaves, or other debris build-
up.  Clean oil or fuel spillage.  Allow machine to cool before
storing.

Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.

Never make adjustments or repairs with the engine
running.

Grass catcher components are subject to wear, damage,
and deterioration, which could expose moving parts or
allow objects to be thrown.  Frequently check components
and replace with manufacturer's recommended parts,
when necessary.

Mower blades are sharp and can cut.  Wrap the blade(s)
or wear gloves, and use extra caution when servicing
them.

Check brake operation frequently.  Adjust and service
as required.

Summary of Contents for 178379

















































Reviews: