Potterton Thames Installation And Servicing Instructions Download

Page: 1 / 23

INSTALLATION AND SERVICE

INSTRUCTIONS

Thames

Gas Fired Water Heater

G.C. NO. 52 476 40

NON SPOUTED MULTIPOINT MODEL

FOR USE WITH NATURAL GAS

THE GAS SAFETY (INSTALLATION AND USE) REGULATIONS 1984.

“In your own interest, and that of safety, it is law that all gas appliances are installed by competent persons, in ac with the

above regulations. Failure to install appliances correctly could lead to prosecution.”

Installation must be in accordance with the Building Regulations, Byelaws of the Water Undertaking, and LE.I Regulations. It

should be in accordance also with any relevant requirements of the Local Gas Region and Local and the relevant

recommendations of the following British Standard Codes of practice: BS 6891, BS 5440:1:2 and BS 5546.

LEAVE THESE INSTRUCTIONS WITH THE USER FOR USE ON FUTURE CALLS

IMPORTANT

PLEASE READ THIS BOOK
BEFORE INSTALLING,
OPERATING OR
SERVICING THIS
APPLIANCE.

Supplied by HeatingSpares247.com

Summary of Contents for Thames
























Search results

Summary of Contents for Thames

Reviews:

Related manuals for Thames

Brands by name

Popular brands

Potterton Thames, Installation And Servicing Instructions

Search results

Summary of Contents for Thames

Reviews:

Related manuals for Thames

Brands by name

Popular brands