Potterton Paramount four Installation Manual Download Page 58

Page: 58 / 144

Operator section

Prog. no.

Level Standard value

Software version

—

(1) This parameter is only visible in the room device.

(2) This parameter is only visible if a suitable standard setting is available in the operating unit.

(3) This parameter is only visible in the room device, as the operating unit in the boiler is programmed permanently to the operating unit.

Wireless

(1)

Prog. no.

Level Standard value

Room unit 1

Missing | In operation | No recept'n | Change batt

130

Missing

Room unit 2

Missing | In operation| No recept'n | Change batt

131

Missing

Room unit 3

Missing | In operation | No recept'n | Change batt

132

Missing

Outside sensor

Missing | In operation| No recept'n | Change batt

133

Missing

Repeater

Missing | In operation| No recept'n | Change batt

134

Missing

Operator unit 1

Missing | In operation| No recept'n | Change batt

135

Missing

Operator unit 2

Missing | In operation| No recept'n | Change batt

136

Missing

Operator unit 3

Missing | In operation| No recept'n | Change batt

137

Missing

Service unit

Missing | In operation| No recept'n | Change batt

138

Missing

Delete all devices

No | Yes

140

(1) Parameters only visible if wireless room device exists.

Time program

Heating cir

cuit 1

Prog. no.

Heating cir

cuit 2

(1)

Prog. no.

Heating cir

cuit 3

Prog. no.

Level Standard value

Select Mon-Sun

Mon-Sun | Mon-Fri | Sat-Sun | Mon | Tue | Wed |

Thu | Fri | Sat | Sun

500

520

540

Mon

1st Time ON

501

521

541

06:00 (h/min)

1st Time OFF

502

522

542

22:00 (h/min)

2nd Time ON

503

523

543

--:-- (h/min)

2nd Time OFF

504

524

544

--:-- (h/min)

3rd Time ON

505

525

545

--:-- (h/min)

3rd Time OFF

506

526

546

--:-- (h/min)

Copy?

515

535

555

Default values

No | Yes

516

536

556

(1) Parameters only visible if heating circuit is installed.

Time program heating circuit 4 / DHW

Prog. no.

Level Standard value

Select Mon-Sun

Mon-Sun | Mon-Fri | Sat-Sun | Mon | Tue | Wed | Thu | Fri | Sat | Sun

560

Mon

1st Time ON

561

05:00 (h/min)

1st Time OFF

562

22:00 (h/min)

2nd Time ON

563

--:-- (h/min)

2nd Time OFF

564

--:-- (h/min)

9 Settings

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Search results

Summary of Contents for Paramount four

Reviews:

Potterton Paramount four, Installation Manual, Page: 58 / 144

Search results

Summary of Contents for Paramount four

Reviews: