background image

DOCUMENT CONTROL INFORMATION

Document Part Number: 

924-010160-001, Rev 7

Publication Date:

March 31, 2004

Document ID:

o03kd000.fm

CONFIDENTIALITY NOTICE

The information contained in this document is the property of Positron Inc. Except as specifically 
authorized in writing by Positron Inc., the holder of this document: 1) shall keep all information 
contained herein confidential and shall protect same in whole or in part from the disclosure and 
dissemination to all third parties, and 2) shall use same for operating and maintenance purposes only.

DISCLAIMER NOTICE

Although Positron Inc. has made every effort to ensure the accuracy of the information contained 
herein, this document is subject to change without notice.

TECHNICAL CUSTOMER SUPPORT

Should a problem arise, contact your customer support department. If the problem cannot be resolved 
by your support department or if you have any questions, contact Positron’s Technical Customer 
Support department at 1-888-577-5254.

© 2004 Positron Inc.

Teleline Isolator is a registered trademark of Positron Inc.

Product names, other than Positron’s, mentioned herein may be trademarks and/or registered trademarks 
of their respective companies.

Summary of Contents for Teleline Isolator 751239





















Reviews: