background image

5. Adding another channel (transmitter) to the motor

To add another channel or another device, start with the transmitter which was 
programmed first. While adding an additional transmitter (channel), do not 
disconnect the motor from power supply! Transmitters must be located within the 
receivers' range

.

1. 

Select a previously programmed channel on the display of the active 

transmitter

.

2. 

Press P2, the motor will make a single beep sound and move briefly up and 

down

3. 

Press P2 again, the motor will make a single beep sound

 again. 

4. 

Press P2 on the device/channel you wish to program. You will hear 5 beeps and 

the motor will move briefly UP and DOWN

.

6. Device operating mode

The PORTOS-RM radio drive can operate in two modes

:

Support mode

Pressing and releasing the UP or DOWN button activates a programmed motor 
function (opening or closing the roller shutter). The motor will operate until the roller 
shutter is fully opened or closed

.

Non-support mode

The motor will only operate when the button is pressed down. Releasing the button 
stops the motor. If the button is pressed down for more than 2 seconds, the motor 
will start operating in the support mode, i.e. until the roller shutter is fully opened or 
closed

.

5

2 x P2

Summary of Contents for PX15T









Reviews: