background image

8- ENG

D25806

PRESSURE WASHER

Gear Reduced High Pressure Pump

:  Increases the pressure of the water sup-

ply.

Engine: 

Drives the high pressure pump.

High Pressure Hose: 

Carries the pressurized water from the pump to the gun

and wand.  

Spray Gun: 

Connects with wand to control water flow rate, direction, and pres-

sure.

Quick Connect Wand: 

Wand is equipped with a female quick connect coupler on

the end.  This allows the user to quickly change out high-pressure nozzles for dif-
ferent spray patterns and change to the soap nozzle for low pressure and chemi-
cal/soap applications. See Operation section.

Chemical Hose (not shown):  

Allows cleaners or cleaning solvents to be mixed

with the pressurized water stream. See How To Siphon Chemicals/Cleaning
Solvents in Operation section of this manual.

OPERATION

Know Your Pressure Washer

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING
YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with
the location of various controls and adjustments. Save this manual for future ref-
erence.

Gear
Reduced High
Pressure
Pump

Engine

High
Pressure
Hose

Spray
Gun

Quick
Connect
Wand

Quick
Connect
Nozzles

Summary of Contents for D25806-025-2





















Reviews: