Porter-Cable CPLMC7580V2C Instruction Manual Download Page 3

3- ENG

D24225

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS 

IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN
SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL
WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.

RISK OF EXPLOSION OR FIRE

ALWAYS 

OPERATE THE COMPRESSOR IN A

WELL VENTILATED 

AREA FREE OF

COMBUSTIBLE MATERIALS, GASOLINE OR
SOLVENT VAPORS. 

IF SPRAYING FLAMMABLE MATERIALS,

LOCATE COMPRESSOR AT LEAST 20 FEET
AWAY FROM SPRAY AREA. 

AN ADDITIONAL

LENGTH OF HOSE MAY BE REQUIRED.

STORE FLAMMABLE MATERIALS IN A
SECURE LOCATION AWAY FROM
COMPRESSOR.

NEVER PLACE OBJECTS AGAINST OR ON
TOP OF COMPRESSOR.  OPERATE
COMPRESSOR

IN AN OPEN AREA 

AT LEAST

12 INCHES AWAY FROM

ANY  WALL OR

OBSTRUCTION

THAT WOULD RESTRICT THE

FLOW OF FRESH AIR TO THE VENTILATION
OPENINGS.

OPERATE COMPRESSOR IN A CLEAN, DRY,
WELL VENTILATED AREA.  

DO NOT OPERATE

UNIT INDOORS OR IN ANY CONFINED AREA.

ALWAYS REMAIN IN ATTENDANCE WITH
THE PRODUCT WHEN IT IS OPERATING.

ALWAYS DISCONNECT ELECTRICAL POWER
BY MOVING PRESSURE SWITCH LEVER TO
THE OFF POSITION AND DRAIN TANK DAILY
OR AFTER EACH USE.

HOW TO PREVENT IT

IT IS NORMAL FOR ELECTRICAL CONTACTS

WITHIN THE MOTOR AND PRESSURE SWITCH

TO SPARK.

IF

ELECTRICAL 

SPARKS

FROM

COMPRESSOR 

COME INTO CONTACT WITH

FLAMMABLE VAPORS, THEY MAY IGNITE,
CAUSING FIRE OR EXPLOSION.

RESTRICTING

ANY OF THE 

COMPRESSOR

VENTILATION OPENINGS 

WILL CAUSE

SERIOUS OVERHEATING AND

COULD CAUSE

FIRE.

UNATTENDED OPERATION 

OF THIS

PRODUCT 

COULD RESULT IN PERSONAL

INJURY OR PROPERTY DAMAGE. TO
REDUCE THE RISK OF FIRE, DO NOT ALLOW
THE COMPRESSOR TO OPERATE
UNATTENDED.

WHAT CAN HAPPEN

HAZARD

Summary of Contents for CPLMC7580V2C



























Reviews: