3
Step 1 :
press 5s to
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
to enter current time setting.
Step 2 :
Press to
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
, the hours
are blinking
, push to
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
and
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
to adjust the hours.
Step 3 :
Press to
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
, the minutes
are blinking
, push to
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
and
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
to adjust the minutes.
Step 4 :
Press to
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
to validate and return to the main screen.
4. Use
When the incoming water temperature is higher or equal to the required temperature (setpoint temperature
+ 1°C), the heat pump will switch to cooling mode. The compressor will stop when the temperature of the
incoming water is less than or equal to the required temperature (setpoint temperature - 1°C).
WARNING:
When the cooling mode switches to heating mode or vice-versa, the heat pump will restart
after 10 minutes.
Good to know
4.6
Setting the clock
By default, time programming is inactive. Therefore, it is necessary to activate it and then create time slots.
Here is the manipulation to activate it:
-Appuyez sur
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
3 seconds pour entrer dans les paramètres à changer. Appuyez sur
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
et
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
pour choisir les
paramètres.
-Press
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
3 seconds to enter the parameters to change. Press
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
and
SET
IN
NO
ROOM
VALUE
OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTO
FAN
h
MIN
%
F
to choose the settings.
-Go to parameter L2
- Set the value to 1
Once done, you can press «clock» to create your schedules.
4.7
On / Off programming
