Poniie PN2000 User Manual Download Page 9

 

1 x PN2000 Digital Electricity Monitor 

1 x User Manual 

1 x 1 Ft. 14AWG Extension Cord 

 

IMPORTANT:

   

1) It is not recommended a long uninterrupted use for loads over 15 amp (1725W 

at 115V). 

2) Please do not overload (1840W at 115V) the device at any time. Failure to 

comply with the instructions given in this manual and/or using the device in ways 

other than the ones mentioned in this manual may result in serious injury and/or 

damage to the product. 

3) The inner and outer device material is ABS fireproofing. If device is over used 

or exposure to excessive heat, it may cause a melt incident. If use open flame to 

light this material, it will be  extinguished  immediately  when  the flame  is 

removed. Still, you need use this device carefully to avoid any fire hazard. 

 

 

The warranty period for quality related issues of this product is one year. If the 

device does not operate properly or has any other faults, please always feel free 

to contact Poniie Customer Service at any time. We will provide you with best 

service and do our best to help you out. 

 

 

Summary of Contents for PN2000










Reviews: