background image

 

PN: 1725-36031-001_H.doc 

49

Safety Notices 

 

WARNING: 

 Changes or modifications to this equipment not 

approved by SpectraLink Corporation may cause this equipment to 
not comply with part 15 of the FCC rules and void the user’s 
authority to operate this equipment.

 

 

 

WARNING: 

 SpectraLink products contain no user-serviceable 

parts inside.

 

Refer servicing to qualified service personnel.

 

 

 

IMPORTANT SAFETY INFORMATION

 

Follow these general precautions while installing telephone 
equipment: 

  Never install telephone wiring during a lightning storm. 

  Never install telephone jacks in wet locations unless the jack is 

specifically designed for wet locations. 

  Never touch uninsulated telephone wires or terminals unless 

the telephone line has been disconnected at the network 
interface. 

  Use caution when installing or modifying telephone lines 

  When installing Base Stations outside or in buildings other than 

the one containing the System Controller, take the following 
precaution: 
If wiring for a Base Station exits a building—whether to reach 
an outdoor Base Station location or to reach a Base Station in 
another building—the wiring must be protected at both ends by 
a Quick Clip Fuse from Illinois Tool Works, Linx Division, model 
number SCP-2X2. The Quick Clip Fuse replaces the bridging 
clips on the 66 blocks for all four connections to the non-internal 
Base Station. 

 

VoIPon   www.voipon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for SpectraLink 8000 System




















































Reviews: