background image

POLY-PLANAR  •  PO Box 409   •  Hanover, MD 21076

Tel: (410) 761-4000 • Fax: (410) 761-6274 • www.polyplanar.com

POLY-PLANAR  •  PO Box 409   •  Hanover, MD 21076

Tel: (410) 761-4000 • Fax: (410) 761-6274 • www.polyplanar.com

12

ME-400 Marine Amplifier

The  ME-400  four  channel,  marine-grade  amplifier  provides  400  watts  of  crisp,  clean 
audio power.  The amplifier can be easily configured to enhance your listening pleasure.  
Both crossover circuits and high pass and low pass filters are fully adjustable so you can 
power  your  subwoofer  as  well  as  your  standard  speakers.    Gold  plated  connections 
resist  corrosion.    Rubber  mounting  feet  isolate  vibration.    Efficient  heat  sink  design 
ensures uninterrupted operation.  Built from the ground up to withstand the rigors of 
the marine environment, the ME-400 will be an outstanding addition to your vessel’s 
audio system.

Introduction

• Circuit board and connectors optimized for marine use
• Mosfet PWM power supply
• 2 ohm stable stereo outputs
• Bridgeable outputs
• Variable input level controls for each pair of channels
• Variable High-pass, Low-pass and All-pass crossover.
• Variable Bass Boost circuit
• Thermal and overload protection circuitry
• Gold-plated RCA jacks and terminals
• Rubber isolation mounting feet

ME-400 Features

PLEASE READ THIS MANUAL BEFORE  

INSTALLATION AND USING AMPLIFIER

Poly-Planar products are warranted to be free of defects in materials and workmanship 

for a period of two years. No finished goods or parts may be returned for repair or 

replacement  without  Poly-Planar  authorization.  Goods  received  for  any  reason  other 

than  out-of-box  defect  will  be  returned  freight  collect.  To  qualify  as  an  out-of-box 

defect, the product must be found defective within 30 days of retail sale. Please call 
Poly-Planar  Customer  Service  for  authorization,  which  will  take  the  form  of  an  RMA 
(Return Merchandise Authorization) number. Warranty is subject to proper installation 
and operation within published specifications. Poly-Planar will repair or replace, at its 
discretion, any unit returned to its factory and determined to be defective. Poly-Planar 

is not liable for consequential damages.

Poly-Planar Warranty

1

Summary of Contents for ME-400







Reviews: