VAPORETTO SYSTEM PRO
59
E
E
N
N
G
G
L
L
I
I
S
S
H
H
testing in order to find the jet which is more
suitable to the fabric to be ironed.
IMPORTANT NOTE
• Do not leave the iron unattended whilst con-
nected to the mains.
• Iron only on heat resistant surfaces and on
surfaces that allow the steam to escape e.g.
mesh ironing boards.
• In case of accidental fall of the appliance it is
necessary to have it checked by an author-
ized service center as the internal safety fea-
tures may have been affected.
•
ATTENTION: if you iron sitting down, do not
place your legs under the ironing board, the
steam can cause burns.
T
T
U
U
R
R
B
B
O
O
B
B
R
R
U
U
S
S
H
H
(
(
T
T
B
B
)
)
(
(
O
O
P
P
T
T
I
I
O
O
N
N
A
A
L
L
)
)
The turbo brush uses a turbine system which
operates on suction power only, without electri-
city.
The turbo brush increases the effectiveness
and efficiency of suction on soft furnishings
such as carpets and fitted carpeting since it
combines suction with a mechanical action to
remove dust and dirt (organic and inorganic)
and fibres (hair, etc.). By using the turbo-brush
on carpets you can refresh the fibres thanks to
the action of the roller, which separates them
so that the cleaner can reach right down into
the carpets.
The turbo brush can be used as a traditional
brush on hard surfaces since it has a by-pass
system which diverts the air flow directly to the
suction pipe.
Use: A cursor on the back of the turbo brush
permits you to adapt it to any kind of surface:
slide the cursor (
TB1
) to the left for hard surfa-
ces, and slide it to the right for carpets and fit-
ted carpeting. The cursor adjusts the speed of
the turbine system: when it is moved comple-
tely to the right, the turbine works at the maxi-
mum rotation speed, while when it is moved
completely to the left there is no rotation and
the brush operates as a normal floor brush.
The turbine can be easily accessed for clea-
ning thanks to the practical flap (fig.12).
G
G
E
E
N
N
E
E
R
R
A
A
L
L
M
M
A
A
I
I
N
N
T
T
E
E
N
N
A
A
N
N
C
C
E
E
Before carrying out any type of maintenance
make sure that the power cable has been dis-
connected from the mains.
After using the brushes it is advisable to allow
the bristles to cool in their natural position so as
to avoid them getting deformed in any way.
Check the conditions of the gaskets located in-
side the monobloc plug (
B2
) periodically.
If necessary, replace them with the appropriate
spares. Also carry out the same check on the
gaskets for connecting the extension tubes (
D
)
and the handle (
A2
).
To clean the outside of the appliance, just use a
damp cloth. Do not use solvents or detergents
as these might damage the plastic surface.
C
C
L
L
E
E
A
A
N
N
I
I
N
N
G
G
T
T
H
H
E
E
G
G
O
O
R
R
E
E
®
®
.
.
C
C
L
L
E
E
A
A
N
N
S
S
T
T
R
R
E
E
A
A
M
M
®
®
F
F
I
I
L
L
T
T
E
E
R
R
IMPORTANT
: the filter provided with Vaporetto
is washable. Proceed as follows to clean it:
• Remove the water container (
20
) using the
handle provided (
22
) (fig.4).
• Remove the filter lid (18) using the handle
(
19
).
• Turn the GORE
®
CLEANSTREAM
®
filter
(
17
) anti-clockwise and pull it off the filter lid
(
18
) (fig.11).
• Rinse the GORE
®
CLEANSTREAM
®
filter
under running water to remove dirt.
• Let the filter dry before connecting it up to the
filter lid again.
IMPORTANT:
• Do not clean the filter with brushes, rags or
any other object that may have abrasive po-
wer, as rubbing or patting it may damage the
filter and decreasing its filtering capacity.
• Do not use detergent, do not rub the filter
and do not wash it in the dishwasher
GORE
®
CLEANSTREAM
®
, GORE-TEX
®
and
Designs are trademarks of W. L. Gore & Asso-
ciates, Inc.
VT SISTEM PRO - M0S08405 2O07:Layout 1
16/07/2008
13.56
Pagina 59
Summary of Contents for VAPORETTO SYSTEME PRO
Page 1: ......
Page 15: ...NOTE...
