ENGLISH
VAPORETTO ACTION
20
• Unscrew the screw (
C
) from the appliance (
A
),
using an appropriate screwdriver. Connect the
appliance (
A)
to the brush (
10
) and tighten the
screw (
C
) (Fig. 2).
• Remove the water tank (
5
) from the appliance
pulling it upward (Fig. 3). Unscrew the cap with
the water take-up hose and remove it from the
tank (Fig. 4).
• Fill the tank with water using the jug supplied
(Fig. 5). Water by its nature contains limescale
which, as time goes by, can cause problems. To
protect your appliance, use demineralised water.
Do not add other substances or additives to the
tank.
• Screw the cap with the water take-up hose back
on the tank and hook it back on the appliance
(Fig. 6).
• Position the cloth (
11
) under the brush (Fig. 7)
and fasten it by pulling the cord (Fig. 8).
USE
• Plug the power lead (
4
) into a suitable socket
with an earth connection. The power indicator
light will come on (
8
).
• The power indicator light (
8
) will remain on con-
stantly indicating that the appliance is connected
to the mains.
• Wait for the pressure indicator lamp (
9
) to come
on. At this point the appliance is ready for use.
• To release the brush (
10
) from the appliance, put
your foot on the brush (
10
) and at the same time
tilt the handle (
1
) (Fig. 10). To block it again, just
return it to the original position (Fig. 10).
• Press the steam button (
2
) to dispense steam. To
stop it, release the steam button (
2
).
• Clean the floors by moving the brush forward and
backward.
• To clean rugs and carpets, rest the brush (with
the cloth attached) on the special frame (
12
) so
that it can slide on the surface (Fig. 9).
NOTE:
the steam ready light (
9
) turns on and off
during use. This indicates that the electric resistan-
ce is operating to keep temperature constant and is
therefore quite normal.
Warning:
- To remove the cloth from the brush, detach
the power supply plug from the electric
socket and wait a few minutes to allow the
cloth to cool.
NO WATER
When the water inside the tank (
5
) runs out, steam
will stop being emitted and a considerable increase
in noise will be heard. In any case, the water level
is always visible thanks to the transparent tank.
To restart operations just fill the water tank (
5
)
again as described in the paragraph “PREPARA-
TION”.
Warning: This operation must always be done
by disconnecting the appliance from the mains.
LIMESCALE FILTER
By nature, water contains mineral salts that favour
the formation of scale.
Vaporetto Action is supplied with a limescale filter
(
7
) which reduces the passage of mineral salts and
therefore the formation of limescale.
Always use demineralised water.
We recommend that the filter be changed 2 times
per year.
To replace the filter, proceed as follows:
• Unplug from the mains electricity.
• Remove the water tank (
5
) (Fig. 3) pulling it
upward, then remove the filter (
7
), still pulling
upward (Fig. 13).
• Position the new filter (
7
), push gently and make
sure that it is perfectly inserted (Fig. 13), then re-
position the water tank (Fig. 6).
Inside the package there is a spare filter (
7
), in addi-
tion to the one already mounted on the appliance.
STORING THE DEVICE
After use, proceed as follows before putting the
appliance away:
- unplug the power supply from the mains.
- completely empty the water tank
(5)
to avoid
water leaks
- detach the cloth from the brush, waiting a few
minutes to allow it to cool.
- wind the power supply cable around the special
cable rewinds (
3
) and (
6
) before replacing the
appliance.
Warning:
- Before using the appliance again, remember
to unwind the power cable completely.
- Do not keep the appliance connected to the
power supply with the cable wound up.
PRACTICAL ADVICE FOR THE USE
VT ACTION_7:FEV 1000-950.qxd
04/09/2012
16.58
Pagina 20
Summary of Contents for Vaporetto Action
Page 1: ...ACTION ...