E
E
N
N
G
G
L
L
I
I
S
S
H
H
VL FOREVER 980 / FOCUS STEAM / PRO - 970 ANTI-SHINE
30
NOTE:
• Both (
5
) and (
11
) lights go on and off during
operation; this is quite normal and means
that the electric resistance is operating to
maintain constant the pressure in the boil-
er.
• If no steam is released from the iron, check
that the steam pressure light (
5
) is off.
C
C
L
L
E
E
A
A
N
N
I
I
N
N
G
G
T
T
H
H
E
E
W
W
A
A
T
T
E
E
R
R
F
F
I
I
L
L
T
T
E
E
R
R
If the water filter (
4
) becomes dirty, proceed
as described below:
• Remove the tank lid (
1
).
• Remove the water filter (
4
) (fig.6) from its
place and clean it under running water.
• Put the filter (
4
) back in its place and close
the tank lid.
F
F
I
I
L
L
L
L
I
I
N
N
G
G
T
T
H
H
E
E
T
T
A
A
N
N
K
K
Thanks to the self-filling function, there is no
longer any need to stop and wait while the
boiler fills up again.
When the water inside the boiler reaches its
low level, the thermostat will automatically
activate a pump that will fill the boiler from the
tank.
It is necessary to refill the feeder tank with
water before it becomes empty.
If, on pressing the steam request button no
steam comes out and you also hear the
pump noise increase, it means that there is
no more water in the tank.
To keep on working, simply restore the water
level in the self-refilling tank as described in
the “Preparation for use” paragraph.
C
C
A
A
R
R
E
E
O
O
F
F
Y
Y
O
O
U
U
R
R
V
V
A
A
P
P
O
O
R
R
E
E
L
L
L
L
A
A
•
Before attempting any maintenance
operation, always disconnect the ap-
pliance from the mains.
• To clean the body of the appliance, simply
use a moist cloth. Do not use solvents or
detergents which may harm the body mate-
rial.
C
C
L
L
E
E
A
A
N
N
I
I
N
N
G
G
T
T
H
H
E
E
B
B
O
O
I
I
L
L
E
E
R
R
• Disconnect the appliance and let it cool
down for at least 2 hours.
• Empty the water tank to prevent leakage.
• Turn the appliance upside-down and use
the hexagon wrench (
13
) to unscrew the
boiler cap (
12
) on the bottom of the ap-
pliance (fig.7).
• Use the funnel (
14
) to pour 1/4 litre of cold
water into the boiler.
CAUTION: do not pour more than the
specified amount of water into the boi-
ler. Pour water slowly, being careful not
to let it overflow, as this could damage
the appliance (fig.8).
• Rinse out the boiler and pour the water
away into the sink or into a container for
collecting dirty water.
• If the water is very dirty, repeat the opera-
tion until it is clean.
• Put the cap back on the boiler, checking
that the seal is present and that the cap is
screwed on properly.
• Fill the water tank again and put the cap
on.
• Turn the appliance on again.
• Before ironing, release steam into the sink
or another container and check that the
steam is clean. This should take a few se-
conds.
• Resume ironing normally.
• To maintain optimum performance, clean
the boiler every 10/20 uses depending on
the amount of limestone in the water.
VL FOREVER 980-970 M0S09407 1Q08:FEV 1000-950.qxd
15/09/2010
10.45
Pagina 30
Summary of Contents for VAPORELLA FOREVER 980 PRO
Page 1: ......
Page 8: ...N O T E 31...
