A R O M A
M I C H E L A N G E L O
8
EE
EE
NN
NN
GG
GG
LL
LL
II
II
SS
SS
HH
HH
As a reminder, you may set the replacement date
on the wheel on the top of the filter.
For more thorough prevention of lime scale
build-up, you should run the “lime scale re-
moval” programme at least once a year even
if you regularly use the resin-based filter.
Without filter
If you no longer want to use the filter, you must re-
programme the filter setting to “NO”.
This is important as you must use the lime
scale removal programme if you are not using
the filter.
1c. Press the programming button
P
.
2c. Press
>
until the words PROGRAM FILTER ap-
pear on the display.
3c. Press
ok
.
4c. Press
>
again until NO appears on the display.
5c. Confirm by pressing
ok
. The words PROGRAM
FILTER will appear on the display.
6c. From this position you may continue program-
ming or exit by pressing
exit
.
Don’t forget to programme water hardness when
not using the filter.
2. WATER HARDNESS
The frequency of lime scale removal depends on
the hardness of your local water supply. Set water
hardness correctly as soon as you begin using the
machine so that the system will be able to inform
you when the lime scale procedure is necessary.
First test the water using the litmus paper (
26
) sup-
plied:
Fill a small container with tap water. Dip the litmus
paper into it and remove it immediately, then shake
it gently.
After about one minute you will be able to read the
results by counting the red dots.
Different levels are distributed as shown below:
–
1 red dot =
1 -7° dH / 1 - 12.6°fH
= LEVEL 1
–
2 red dots =
8 -14° dH / 12.7 -25.2°fH = LEVEL 2
–
3 red dots =
15-21° dH / 25.3-37.8°fH = LEVEL 3
–
4 red dots
= > 21° dH / > 37.8°fH
= LEVEL 4
When no red dots are visible, set on level 1.
The factory setting corresponds to LEVEL 3.
1d. Press the programming button
P
.
2d. Press
>
until PROGRAM W. HARD appears on
the display. (It will appear only if the filter is pro-
grammed to NO).
3d. Press
ok
.
4d. Press
>
again until the level of water hardness
determined in the litmus paper test appears on
the display.
5d. Confirm by pressing
ok
, and the words PRO-
GRAM W. HARD will appear on the display.
From this position you may continue programming
or exit by pressing exit.
3. TEMPERATURE
You may change coffee temperature to suit your
preferences, setting it to NORMAL, HIGH or MAXI-
MUM.
The factory setting is “
High
”.
1e. Press the programming button
P
.
2e. Press
>
until PROGRAM.TEMP. appears on the
display.
3e. Press
ok
.
4e. Press
>
again until the desired temperature lev-
el appears on the display.
5e. Confirm by pressing
ok
, and PROGRAM.TEMP.
will appear on the display.
6e. From this position you may continue program-
ming or exit by pressing
exit
.
4. TIME
You must programme the current time before you
can programme on time.
1f. Press the programming button
P
to go into Pro-
gramming mode.
2f. Press
>
until PROGRAM. TIMES appears on the
display.
3f. Press
ok
, and TIME SETTING will appear on the
display.
4f. Confirm by pressing
ok
. HOURS > 00:00 will
appear on the display. (the arrow will flash)
5f. Press
>
until the desired time appears.
6f. Confirm by pressing
ok
. The
<
arrow will start
flashing behind the minutes.
7f. Press
>
until the minutes are correct.
8f. Confirm by pressing
ok,
and TIME SETTING will
appear on the display.
9f. From this position you may continue program-
ming or exit by pressing
exit
.
Important: The time setting will be lost if you turn
