T
T
R
R
A
A
N
N
S
S
M
M
I
I
T
T
T
T
E
E
R
R
D
D
I
I
S
S
P
P
L
L
A
A
Y
Y
P
P
A
A
N
N
E
E
L
L
I
I
C
C
O
O
N
N
D
D
E
E
S
S
C
C
R
R
I
I
P
P
T
T
I
I
O
O
N
N
The transmitter display panel has 6 icons that will flash in red to display the successful
operation of the command that has been requested.
The 6 icons are displayed on the remote as follows:
TRANSMITTER DISPLAY PANEL EXPLANATIONS
Condition
Display Panel Icon
Flashes
Beeps
Cold Weather Timer
ON (Press & Hold
STOP button)
STOP
then
START & SIREN
1
then
2
1
Cold Weather Timer
OFF (Press & Hold
STOP button)
STOP
Then
STOP & SIREN
1
then
2
1
Shock Sensor Alert
LOCK &
STOP & SIREN
Flashing for 10
seconds
*Beeps for 10
seconds
Silent for 10 seconds
State of Alarm
(Siren is ringing)
All Icons flashing
Flashing for 10
seconds
*Beeps for 10
seconds
Silent for 10 Seconds
Engine Running
START
2
2
* Will keep beeping until a button is pressed or for a total of 2 minutes.
SYSTEM OPERATIONS
This unit is a state-of-the-art combination of a vehicle alarm and remote starter system.
Start by familiarizing yourself with the alarm functions of the unit before using the remote
starter functions. This is especially recommended if your unit is set in Passive Arming
Mode.
BEEPS DISABLED
You can disable the transmitter confirmation beeps by pressing the TRUNK button 5
times (1 beep confirms that the beeps are disabled). To re-enable the beeps, press the
TRUNK button 5 times again within 3 seconds (3 beeps confirm that the beeps are
enabled).
NOTE:
The 2 beeps confirming that the engine is running during the Status Request
are not disabled by this option.
VEHICLE STATUS REQUEST
The two-way transmitter has a built in feature that will allow the user to contact the
vehicle by remote and get a report of it’s current condition displayed on the remote’s
information panel.
To request a status check, press and hold the LOCK & STOP buttons simultaneously.
Condition
Icon
Flashes
Beeps
Engine OFF / Cold
Weather Timer OFF
None
None
2
Engine ON / Cold
Weather Timer OFF
START
2
2
Engine OFF / Cold
Weather Timer ON
SIREN
2
2
Engine ON / Cold
Weather Timer ON
SIREN & START
2
2
Valet Mode
STOP & START
2
2
Armed/Locked
LOCK
1
1
Disarmed/Unlocked
UNLOCK
1
1
LOW BATTERY WARNING
The transmitter uses one 1.5 volt AAA battery that should be replaced when the Low
Battery warning occurs. If the battery voltage is getting weak, the remote will give a
warning when transmitting. All the icons on the display panel will flash 3 times to
indicate that the battery should be replaced.
E
E
X
X
T
T
E
E
N
N
D
D
I
I
N
N
G
G
R
R
E
E
M
M
O
O
T
T
E
E
B
B
A
A
T
T
T
T
E
E
R
R
Y
Y
L
L
I
I
F
F
E
E
To extend remote battery life, the system can be placed in battery saver
mode by
pressing the STOP and UNLOCK buttons simultaneously for approximately 5 seconds.
The TRANSMIT icon on the display panel will become constant. To take the system
out of battery saver mode, press the STOP and UNLOCK buttons simultaneously until
the TRANSMIT icon is flashing.
NOTE:
Placing the system in battery saver mode will disable the ability of your
remote to receive the confirmation of an alarm condition from your vehicle.
2
7
Transmitting icon
Lock Icon
Unlock Icon
Stop Icon
Start Icon
Siren Icon
