Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 60

Page: 60 / 147

NOTE

Within the recommended speed ranges (page 58), you can downshift to slow

the vehicle or to increase power. You may want to downshift when climbing a

hill or passing. Downshifting also helps to decrease speed when combined

with releasing the throttle pedal.

7. To shift to a lower gear (downshift), reduce speed to the recommended shift

point. See page 58. Perform the following actions quickly and precisely:

a. Simultaneously release the throttle pedal completely while disengaging

the clutch (depressing the clutch pedal).

b. Move the shift lever to the next lower gear.

c. Simultaneously release the clutch pedal while depressing the throttle

pedal.

WARNING

Downshifting improperly could cause transmission damage, loss of traction

and loss of control, which could result in serious injury or death.

• Reduce speed before downshifting. Always downshift within the

recommended shift points.

• Use extreme caution when downshifting on wet, slippery or other low traction

surfaces. Release the clutch pedal very gradually in these conditions.

• Avoid downshifting in a curve. Downshift before entering the curve. Avoid

coasting (clutch disengaged) through curves and corners.

RECOMMENDED SHIFT POINTS

UPSHIFTING (ACCELERATING)

DOWNSHIFTING (DECELERATING)

GEAR

CHANGE

RECOMMENDED

SPEED

GEAR CHANGE

RECOMMENDED

SPEED

1 to 2

15 MPH (24 km/h)

5 to 4

40 MPH (64 km/h)

2 to 3

25 MPH (40 km/h)

4 to 3

35 MPH (56 km/h)

3 to 4

40 MPH (64 km/h)

3 to 2

20 MPH (32 km/h)

4 to 5

45 MPH (72 km/h)

De-clutch

15 MPH (24 km/h)

OPERATION

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands