Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 45

Page: 45 / 147

3. Release the strap, it will self-tighten.

WARNING

Failure to wear the seat belt properly could result in serious injury or death.

Wear the shoulder belt on the inside shoulder only. Never wear the shoulder

belt under your arm or behind your body.

4. To release the seat belt, press the square red button

at the center of the

latch housing.

SEAT BELT INSPECTION

Inspect all seat belts for proper operation before each use of the vehicle.

1. Push the latch plate into the latch housing until it clicks. The latch plate must

slide smoothly into the housing. A click indicates that it’s securely latched.

2. Push the red release latch at the center of the latch housing to make sure it

releases freely.

3. Pull each seat belt completely out and inspect the full length for any damage,

including cuts, wear, fraying or stiffness. If any damage is found, or if the seat
belt does not operate properly, have the seat belt system checked and/or
replaced by your authorized dealer or another qualified person.

4. To clean dirt or debris from the seat belts, sponge the straps with mild soap

and water. Do not use bleach, dye or household detergents.

FEATURES AND CONTROLS

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands