Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 38 | Manualshive

Page: 38 / 147

background image

ADJUSTABLE SEATS

SEATBACK ADJUSTMENTS

Lift and hold the seat adjustment lever

q

to release the seatback latch. Adjust

seatback angle or tilt the seatback forward to access the storage compartment.
Release the lever. After adjusting, make sure the seatback latches securely in
place

DRIVER’S SEAT ADJUSTMENTS

To adjust the driver’s seat forward or rearward, pull upward on the bar under the
front edge of the seat. Slide the seat to the desired position and release the
lever. Make sure the seat latches securely in place.

WARNING

Making adjustments while driving could result in loss of control. Never make

adjustments while driving.

ADJUSTABLE STEERING WHEEL

The steering wheel can be tilted upward or downward for rider preference.

WARNING

Making adjustments while driving could result in loss of control. Never make

adjustments while driving.

36

FEATURES AND CONTROLS

Downloaded from

«
...
36
37
38
39
40
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Brand: Suzuki Pages: 353

Brand: Torklift Pages: 16

Brand: Carcomm Pages: 2

Brand: Whispbar Pages: 14

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: MAXWORKS Pages: 7

Brand: Quadratec Pages: 12

Brand: Hank Pages: 2

Brand: Velleman Pages: 12

Sedan CIVIC 2022

Brand: Honda Pages: 701

Brand: Honda Pages: 124

Bluetooth Kit3 PLUS

Brand: N-Com Pages: 36

Brand: Mercedes-Benz Pages: 398

2004 JR41 Stratus Sedan

Brand: Dodge Pages: 273

Brand: PERODUA Pages: 43

Brand: Skoda Pages: 276

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands