Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 27

Page: 27 / 147

INSTRUMENT CLUSTER

The instrument cluster includes the indicator lamps

, speedometer

, multi-

function display

and tachometer

SPEEDOMETER

The speedometer displays vehicle speed in either miles per hour or kilometers
per hour. See page 28.

TACHOMETER

The tachometer displays engine speed in revolutions per minute (RPM). A red
line on the face of the gauge indicates the maximum safe engine speed.

WARNING

Excessive engine speed can cause engine damage or failure, which could

result in serious injury or death. Do not allow engine speed to exceed the red

line.

INDICATOR LAMPS

LAMP

INDICATES

CONDITION

Cruise Control
Engaged

Before using the cruise control, read the safety and
operation procedures. See page 61.

Anti-Lock
Brake System

Your dealer can assist if this lamp remains on. When the
lamp is illuminated, the anti-lock brakes will not activate,
but the conventional brake system will continue to operate
normally.

High Beam

This lamp illuminates when the headlamp switch is set to
high beam.

FEATURES AND CONTROLS

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands