Polaris RANGER CREW 900 2014 Manual Download Page 156

Page: 156 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

4.7

EFI SYSTEM COMPONENT LOCATIONS

Electronic Control Unit (ECU)

Located

under

the

passenger

seat.

(Rear

passenger seat on CREW 900).

Electronic Throttle Control (ETC)

- Located between the intake boot and intake
plenum.

Crankshaft Position Sensor (CPS)

- Located on top of the stator cover.

Temperature

Manifold

Absolute

Pressure

Sensor (T-MAP)

- Located on top of the intake plenum.

Engine Coolant Temperature Sensor (ECT)

- Located on the cylinder head below the intake
manifold.

FUEL SYSTEM - GENERAL

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands