Polaris RANGER CREW 900 2014 Manual Download Page 131

Page: 131 / 447

3.74

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

28. Torque oil cooler retaining bolts to specification.

TORQUE

Oil Cooler Retaining Bolts:

7 ft-lb (10 Nm)

29. Proceed to Flywheel Installation, page 3.74 and then

Cylinder Head Installation, page 3.77.

FLYWHEEL INSTALLATION

If previously removed, reinstall the flywheel key.

Clean taper of crankshaft to remove all oil or grease.

Clean flywheel taper to remove all oil or grease.

Align flywheel key-way with key and install the
flywheel, seating it fully on taper.

Install flywheel retaining bolt. Using a commercially
available strap wrench, hold the flywheel and torque
the flywheel retaining bolt

to specification.

NOTE

If the Cylinder Holding & Camshaft Timing Plate (PU-

50563) is installed, remove it before tightening the

flywheel.

TORQUE

Flywheel Retaining Bolt:

133 ft-lbs (180 Nm)

Install the starter torque limit gear as an assembly.

ENGINE

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands