background image

60

OPERATION

Driving Safely

Driving Through Water

Your PTV 6X6 can operate through water with a maximum

recommended depth equal to the footrests. Follow these procedures

when operating through water :
1. Determine water depths and current before crossing.
2. Choose a crossing where both banks have gradual inclines.
3. Proceed slowly, avoiding rocks and obstacles if possible.
4. After crossing, dry the brakes by applying light pressure to the

lever until braking action is normal.

NOTE:

Avoid operating the ATV through deep or fast-flowing water.

If you cannot avoid water that exceeds the recommended maximum

depth, go slowly, balance your weight carefully, avoid sudden

movements, and maintain a slow and steady forward motion. Do not

make sudden turns or stops, and do not make sudden throttle changes.

IMPORTANT:

After running the vehicle in water, it’s

critical

to have

it serviced as outlined in the maintenance chart. See pages 67-69. The

following areas need special attention: engine oil, transmission oil,

front and rear gearcases, and all grease fittings.

Major engine damage can result if the vehicle is not thoroughly

inspected after becoming immersed. If your vehicle becomes

immersed or is operated in water that exceeds the footrest level,

take it to your dealer for service before starting the engine.

CAUTION

Summary of Contents for PTV 6x6 SERIES 10
























































































































Reviews: