manualshive.com logo in svg

Polaris Power P3000iE, Operator'S Manual, Page: 71 / 81

Share
Download
Polaris Power P3000iE Operator'S Manual Download Page 71

70

TROUBLESHOOTING

Troubleshooting Symptoms

No Power at DC Receptacle

POSSIBLE LEAN 

FUEL CAUSE

SOLUTION

Low or contaminated fuel

Add fuel, or drain the fuel system and refuel

Kinked or plugged fuel tank 

vent 

Inspect and replace

Low octane fuel

Drain the fuel system and refuel

Carburetor jetting incorrect Take the generator to an authorized POLARIS servicing 

supplier or refer to the service manual

POSSIBLE RICH 

FUEL CAUSE

SOLUTION

Incorrect fuel

Drain the fuel system and refuel

Stopping / starting without 

adequate warm-up

Allow the engine to warm up before operating and / or 

stopping

Incorrect spark plug

Inspect and replace with correct plug

Clogged air filter 

Inspect and clean or replace

POSSIBLE CAUSE

SOLUTION

Is the fuse blown

Replace the fuse.

Faulty generator

Take the generator to an authorized POLARIS servicing 

supplier or refer to the service manual

Summary of Contents for Power P3000iE


















































































Reviews:

No comments