Polaris Frontier Classic Owner'S Manual Download

Page: 113 / 136

111

MAINTENANCE

Extended Storage

Bearings

Grease the jackshaft and drive shaft clutch side bearings with Polaris

Premium All-Season Grease or a similar high quality grease to prevent

corrosion. See page 124 for part numbers.

Clutch and Drive System

Remove the drive belt and store in a cool dry location. Lubricate the

sheave faces of the drive and driven clutches with a light coat of oil or

Polaris Cable Lubricant. See page 124 for part numbers. Do not

lubricate clutch components, except the driven clutch shaft bushing as

outlined in the Master Repair Manual. See your dealer.

Electrical Connections

Separate the electrical connector blocks and clean any corrosive

build-up from the connectors. Lubricate or pack the connector blocks

with dielectric grease and re-connect.

NOTE:

Do not grease the TPS

connector.
Replace worn or frayed electrical wire and connectors. Be sure the

wiring harness is properly secured away from sharp edges, steering

linkage, moving parts, and hot exhaust parts.

Battery

Always prepare and maintain the battery as outlined on page 115.

Tampering with the EFI connections could result in damage to the

vehicle. Do not remove the engine EFI connections. See your

Polaris dealer for all EFI system service.

CAUTION

Summary of Contents for Frontier Classic









































































































































Search results

Summary of Contents for Frontier Classic

Reviews:

Related manuals for Frontier Classic

Brands by name

Popular brands

Polaris Frontier Classic, Owner'S Manual

Search results

Summary of Contents for Frontier Classic

Reviews:

Related manuals for Frontier Classic

Brands by name

Popular brands