Polaris ATP 330 4x4 Owner'S Manual Download

Page: 83 / 141

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

NOTE:

Hours are based on 10 mph average. If service is due at 20

hours, the equivalent odometer reading would be 200 miles. Perform

all services at whichever reading is reached first.

Lubrication Chart Key

More often under severe use, such as wet or dusty conditions

Polaris Premium All Season Grease or grease conforming to NLG

No. 2, such as Conoco Superlube M or Mobilegrease Special

Use Polaris Premium U-Joint Lube every 500 miles, before long

periods of storage, or after pressure washing or submerging

Item

Lube

Method

Frequency

Engine

Polaris Premium 4

Synthetic 0W40

Add to proper level on dip-

stick.

Check level daily.

Brakes

DOT 3 fluid only

Maintain level between fill

lines. See page 40.

As required; change

every two years or

200 hours

Transmission

Polaris Premium

Synthetic gear

case lube

See Page 88.

Check every 6

months/1000 miles.

Change annually or

at 100 hours

Front Gear-

case

Polaris Premium

Synthetic gear

case lube

See Page 89.

Change annually or

at 100 hours

Front Prop

Shaft U-joints

Grease

Grease fittings.

Every 3 months or

50 hours

Front Prop

Shaft Yoke

Grease

Grease fittings

(3 pumps maximum)

Every 3 months or

50 hours

Front Drive

Axle (U Joint)

Grease

Locate grease fitting and

grease with grease gun.

Every 3 months or

50 hours

Ball Joint

Grease

Locate fitting on back side of

struts and grease with

grease gun.

Every 3 months or

50 hours

Summary of Contents for ATP 330 4x4














































































































































Search results

Summary of Contents for ATP 330 4x4

Reviews:

Related manuals for ATP 330 4x4

Brands by name

Popular brands

Polaris ATP 330 4x4, Owner'S Manual

Search results

Summary of Contents for ATP 330 4x4

Reviews:

Related manuals for ATP 330 4x4

Brands by name

Popular brands