background image

79

MAINTENANCE

POLARIS Recommended Maintenance Program

To ensure many trouble-free miles of snowmobiling enjoyment, follow 
recommended regular maintenance and perform service checks as 
outlined in this manual. Record maintenance and service in the 
Maintenance Log beginning on page 135.

The recommended maintenance schedule on your snowmobile calls for 
service and maintenance inspections at 150 miles (240 km), 500 miles 
(800 km) and 1000 miles (1600 km). These inspections should be 
performed by a qualified service technician. For continued optimum 
performance and component life, continue maintenance checks at 1000 
mile (1600 km) intervals.

All necessary replacement parts and labor incurred, with the exception 
of authorized warranty repairs, become the responsibility of the 
registered owner.

 If, during the course of the warranty period, part 

failures occur as a result of owner neglect in performing recommended 
regular maintenance, the cost of repairs are the responsibility of the 
owner. 

Personal safety is critical when attempting to service or make 
adjustments to your snowmobile. If you're not familiar with safe service 
or adjustment procedures and the use of tools, or if you don't feel 
comfortable performing these tasks yourself, contact an authorized 
POLARIS dealer for service.

NOTICE:

Hot components can cause damage to plastic. Always make sure the 
exhaust system and engine have cooled before tipping the 
snowmobile on its side for service or inspection.

Summary of Contents for 600 PRO RMK















































































































































Reviews: