background image

40

FEATURES

Knock Sensor (Turbo Models)

A knock sensor monitors the engine and responds to detonation by auto-

matically reducing the engine timing and adding fuel. This results in 

decreased engine RPM and performance.
Engine performance will be reduced if fuel with a lower octane than 91 

is used. See fuel recommendations on page 81.

Effect

The knock sensor system prevents damage to the engine from detona-

tion while developing the maximum power of the engine safely. If the 

system senses detonation beyond a preset limit, it retards ignition timing 

and adds fuel to reduce the detonation and prevent engine damage.
When the detonation returns to a permissible level, the system will 

return spark and fuel to normal, allowing the engine to run at rated 

power levels.

Fail-Safe

The knock sensor includes a sensor fail-safe system to prevent the 

engine from damage if the sensor fails, becomes disconnected or is 

unable to detect detonation. The rider will experience a loss in power. 

The sensor must be reconnected or repaired to regain full power.
The check engine light will illuminate if the sensor fails or becomes dis-

connected.

Summary of Contents for 600 IQ Touring 2009






































































































































































Reviews:

Related manuals for 600 IQ Touring 2009