background image

56

OPERATION

Oil

Low Oil Level

Always maintain the oil level between the “add” mark and the bottle 
neck. 

Do not fill the bottle neck.

 See page 51 for oil recommendations.

1.

Immediately

 stop the engine 

if the low oil indicator light 
comes on.

2. Open the right side panel.

3. View the oil level in the oil 

bottle.

4. Add oil as needed before 

operating. 

NOTICE:

Operating the 
snowmobile without 
adequate engine 
lubrication can result in 
serious engine damage. 
Always check the oil level 
when refueling. Add oil as 
needed.

The oil bottle cap is vented to allow proper oil flow. See your POLARIS 
dealer for recommended replacement parts.

Carburetion

NOTICE:

Making non-recommended adjustments could result in vehicle or 
engine damage as well as denial of warranty claims. We recommend 
that all carburetor adjustments be performed by your POLARIS 
dealer. 

Proper carburetor adjustment is critical. A lean mixture (too much air, 
too little fuel) may result in piston burning, bearing failure, or complete 
engine failure.  A rich mixture (too much fuel, too little air) may foul 
plugs and cause generally poor engine performance.  

A lean mixture may be caused by things like fuel line restrictions, 
foreign matter in the carburetor or clogged fuel filters. A rich mixture 
may be caused by snow build-up on the pre-filter in the air intake 
system. Either condition may be caused by improper carburetor 
adjustment.

Bottle 
Neck

ADD 
Mark

Summary of Contents for 2014 550 INDY 144



























































































































Reviews: