background image

4

AU

Telephone Helpline: 1300225960

Installation

Note: If the appliance has 

been stored or moved in a 

non-vertical position, stand 

it in an upright position for 

approximately 12 hours before 

operation. If in doubt allow to 

stand.

1.  Remove the appliance from the packaging and 

remove the protective film from all surfaces.

2.  When positioning the dispenser, maintain 

a distance of 20cm (7 inches) between the 

appliance and walls or other objects for 

ventilation. 

NEVER LOCATE NEXT TO OR 

NEAR A HEAT SOURCE.

3.  If necessary, adjust the screw legs of the 

dispenser to stabilise it.

Assembly/Disassembly

1.  Insert the large rubber gasket into the bottom 

of the tank [Fig. 1].

1

2.  Holding the top and bottom of the tap lever, 

gently bend the lever in the middle [Fig. 2].

3.  Push the two hooks at the back of the tap lever 

into the slot in the front of the tank and drop 

into place [Fig. 3].

4.  Lower the tank on to the cooling column. 

Locate the four feet on the bottom of the tank 

to the mounts on top of the cooling unit.

Note: Lubricate the gasket with 

a small amount of water if the 

gasket is too tight.

2

Hooks

3

Tank

Front

Lever

Slot

5.  Roll the O-ring down 

the tap shaft [Fig. 4] 

and insert thin end 

first into the hole in 

the tank.

6.  Ensure the bottom 

of the tap slots into 

the gap in the tap 

lever.

4

7.  Hang the drip tray from the slots on the front 

of dispenser [Fig. 5].

8.  Insert the mixing paddle rod into the mixing 

paddle [Fig. 6], and lower the rod into the 

cooling column.

5

6

Cooling

Column

9.  Securely fix the lid to the tank.

CF760-A_CF761-A_A5_v3_20190822.indb   4

2019/8/22   09:59

Summary of Contents for CF760-A













Reviews: