background image

Speed Sensor Teaching

The cycling computer has to be coded to the
Speed Sensor i.e. taught to receive speed and
distance data. This enables exercising in a
group without interference from other sensors.

The cycling computer and sensor that come
with the product set have already been
synchronized but teaching is necessary when
you start using a new sensor or if you use other
bike settings than Bike 1.

Install the speed sensor to your bike as advised.
Before you start teaching, make sure that there
are no other speed sensors or cycling computers
nearby (40 m / 130 ft). The procedure only
takes a few seconds. You can teach one sensor
for each bike.

Select

Settings > Bike > Bike 1/2/3 > Speed

.

Select On/Off and On to turn the speed on.
Press OK.

Teach new sensor?

is displayed.

Select YES to confirm teaching. Rotate the
wheel a few times to activate the sensor. The
flashing red light indicates that the sensor is
activated.

Completed

is displayed once the

teaching process is over. The cycling
computer is now ready to receive speed and
distance data.

Select NO to cancel the teaching. The
teaching is cancelled and the cycling
computer resumes contact with the previous
sensor.

To return to Time mode, press and hold the
BACK button.

E N G L I S H

3

Summary of Contents for Cycling Computer









Reviews: