This processor is already programmed with the following (variable) settings.
To return to these settings at any time you may:
Power off the processor, press LUMIN key and keep it pressed giving power on:
boot message will be displayed (release now LUMIN key).
L.SEt = 50.L
.
The COSt values are shown in COSt Programming
PRESET PROGRAMS (Bootstrap)
These settings refer to the operation mode of the system and must be made on
initial startup. Press - / + at the same time for at least one second: the message
C.O.S.t. will be displayed.
Press than repeatedly LIMIN until the message regarding the chosen variable
is displayed (see table below) : value of variable and message will be displayed.
Press + or - to set a new value and then press LUMIN to confirm.
The next system constant will then appear.
You can press LUMIN for at least 2 seconds to exit and return to the Run Mode.
COSt PROGRAMMING (System constants)
*1) For more details see Operative Diagram.
*2) You can correct the readings on the various sensors (+ or -).
.
s
s
e
M
e
u
l
a
V
g
n
i
n
a
e
M
e
t
o
N
b
.
n
L
0
.
5
e
g
n
a
r
l
a
r
t
u
e
n
%
)
1
*
O
L
C
.
b
L
0
.
0
d
n
a
b
n
o
i
t
a
l
u
d
o
m
d
e
s
o
l
c
%
)
1
*
E
P
O
.
b
L
0
.
0
5
d
n
a
b
n
o
i
t
a
l
u
d
o
m
n
e
p
o
%
)
1
*
n
o
.
t
"
0
.
1
s
d
n
o
c
e
s
n
i
e
m
i
t
n
o
)
1
*
F
o
.
t
"
9
.
9
9
s
d
n
o
c
e
s
n
i
e
m
i
t
f
f
o
)
1
*
U
L
.
d
A
n
0
0
.
1
e
b
o
r
p
y
t
i
s
o
n
i
m
u
l
)
t
n
e
i
c
i
f
f
e
o
c
(
r
o
t
c
a
f
e
v
i
t
a
c
i
p
il
t
l
u
m
n
o
i
t
c
e
r
r
o
C
)
2
*
OPERATIVE DIAGRAM
t.On t.oF t.On t.On t.oF t.On
L.SEt
ON OPEN
ON CLOSED
1/2 nb 1/2 nb
b.OPE
b.CLO
n.b.
ON
ON
ON
ON
OFF
OFF
OFF
The lights situated at the bottom of the display show the state of the various relays as set out below.
STATE INDICATION LAMPS
closed action state
open action state
ON CLOSING
ON OPENING
Day condition On:
opening and closing regulation with
luminosity controller.
Night condition On:
completely closed
VIEWING AMBIENT TEMPERATURE RECORDING
Values are permanently stored in the memory: for deleting all values in the memory keep
pushed + key for more than 3 seconds: CLEA message will appear on display before
clearing operation.
Press - :
will be displayed followed by
°Minimum Temperature Recording.
Press + :
will be displayed followed by
°Maximum Temperature Recording.
In some start-up conditions may be useful to work in "manual" mode:
Power off the processor, press + key and keep it pressed giving power on: HAnd
message will be displayed (release now + key).
Press + (1 is displayed) and press LUMIN to activate relay.
You can press LUMIN key for a least two seconds to escape and return to the
Run Mode.
MANUAL MODE