M3x0.5 4
4 PLACES
BOTTOM VIEW
50.00
13.00
26.00
M3x0.5 4
2 PLACES
TOP VIEW
26.00
13.00
SIDE VIEW
8.00
57.50
27.50
FRONT VIEW
C MOUNT LENS THREAD
44.00
29.00
4 PLACES
STATUS LED
BACK VIEW
M3x0.5 4
GPIO CONNECTOR
16.00
22.00
6.26
21.31
SPECIFICATIONS
GS2-FW-14S5M / C
Image Sensor Type
Sony progressive scan interline transfer CCD with square pixels and global shutter
Image Sensor Model
Sony ICX285 2/3”
Max Res
and Max Frame Rate
1384 x 1036 at 30 FPS
Pixel Size
6.45 x 6.45 μm
Analog-to-Digital Converter
Analog Devices 14-bit ADC
Video Data Output
8, 12, 16 and 24-bit digital data
Image Data Formats
Y8, Y16, Mono8, Mono12, Mono16, Raw16 (all models)
RGB, YUV411, YUV422, YUV444, Raw8, Raw12, Raw16 (color model)
Digital Interface
IEEE 1394b 800 Mbit/s interface with screw locks for camera control, data, and power
Partial Image Modes
Pixel binning and region of interest modes available via Format_7
General Purpose I/O Ports
8-pin GPIO connector for power, trigger, strobe, PWM, and serial I/O
1 opto-isolated input, 1 opto-isolated output, 2 bi-directional I/O pins
Gain Control
automatic / manual / one-push gain modes, programmable via software, -3.6dB to 24dB
Shutter Speed
automatic / manual / one-push modes, programmable via software, 0.03ms to 330s (extended shutter mode)
Synchronization
via external trigger, software trigger (on same bus) or free running
External Trigger Modes
External hardware or software trigger
Multiple exposure, bulb shutter, multi-shot, and overlapped trigger modes
Voltage / Power
Voltage: 8-30 V Power: less than 2.5 W
Dimensions (W x H x L)
44mm x 29mm x 58mm (not including lens holder and GPIO connector)
Mass
104 grams (without optics)
Memory Storage
32MB frame buffer, 512 KB non-volatile data fl ash
Memory Channels
2 memory channels for custom camera settings
Camera Speci
fi
cation
Complies with IIDC 1.32
Lens Mount
C-mount
Emissions Compliance
CE, FCC, RoHS
Operating Temperature
0° to 45°C
Storage Temperature
-30° to 60°C
Vibration Resistance
10 G (14 Hz to 200 Hz)
Status Monitoring
Bi-color LED that can be red, green, or yellow
Warranty
2 Years
Off
Not receiving power
Steady on
Receiving power and successful camera initialization
Steady on and very bright
Acquiring / transmitting images
Flashing bright, then brighter
Camera registers being accessed (no image acquisition)
Steady
fl
ashing on and off
Indicates possible camera problem
Slow
fl
ashing on and off
Indicates possible camera problem
STATUS LED
Diagram
Pin
Function
Description
1
IO0
Opto-isolated Input (default Trigger in)
2
IO1
Opto-isoloated Output
3
IO2
Input / Output / RS232 Transmit (TX)
4
IO3
Input / Output / RS232 Receive (RX)
5
GND
Ground for bi-directional IO, V
EXT
, +3.3 V pins
6
GND
Ground for opto-isolated IO pins
7
V
EXT
Allows the camera to be powered externally
8
+3.3V
Power external circuitry up to a total of 150mA
To con
fi
gure the GPIO pins, consult section 3.4 “General Purpose Input / Output” of the
Flea3 Technical Reference Manual
GPIO
The FlyCapture
®
User Guide and other technical references can be
found in the
Programs > Point Grey Research > PGR FlyCapture >
Documentation
directory. Our on-line Knowledge Base
(
www.ptgrey.com/support/kb/
) also addresses the following problems:
• Article 21: Troublesome hardware con
fi
gurations
• Article 88: Vertical bleeding or smearing from a saturated portion of an image
• Article 91: PGR camera not recognized by system and not listed in Device Manager
• Article 93: My laptop’s IEEE-1394 port or PCMCIA card doesn’t supply power to my camera
• Article 145: Image discontinuities or horizontal tearing of images when displayed on monitor
• Article 171: Performance of 1394 devices may decrease after installing Windows XP SP2
• Article 188: Image data acquired by my camera is corrupt and displayed images are broken
• Article 189: Image capture freezes after a period of successful image capture.
Email:
For all general questions about Point Grey Research please contact
us at
.
For technical support (existing customers only) contact
us at
www.ptgrey.com/support/contact/
.
Main Of
fi
ce:
Mailing Address: Tel:
+1 (604) 242-9937
Point Grey Research, Inc.
Toll Free
(N. America only): +1 (866) 765-0827
Richmond B.C. Canada
Fax:
+1 (604) 242-9938
12051 Riverside Way
Email:
V6W 1K7
CONTACTING POINT GREY RESEARCH
3
Troubleshooting
TECHNICAL DRAWINGS
