background image

 

14 

 

ACCESSORIES 

 

The testing of this tool has been accomplished with the following accessories.  For safest 
operation, it is recommended that only these accessories be used with this product. 

 

WARNING

- Since accessories other than those listed have not been tested with this 

product; use of such accessories could be hazardous. 

 

REF.                 PART  
NO.                    NO.  

 

DESCRIPTION 

 

Not Shown       50104 

 

O-Ring Repair Kit 

Not Shown       50172 

 

Grease 

Not Shown      50250 

 

Shoe Base & Pads for 33/32” Flooring 

Not Shown       50246 

 

Shoe Base & Pads for 9/16” Flooring 

Not Shown      50139 

 

Hex Wrenches 

Not Shown       50318 

 

Wrench – Shoe / Body Flange Nuts 

Not Shown       50039 

 

Hammer (Brown Cap for Ram Head, Gray Cap for Floor) 

Not Shown      50299 

 

Hammer Cap (Brown) 

Not Shown       50170  

 

Safety Glasses 

Not Shown       50038  

 

Case - 

PORTAMATIC®

  

Not Shown      42623 

 

Porta-Nails 10 packages of 1000 2” Nails 

 

RECOMMENDED EQUIPMENT 

 

Air Compressor -

  1-1/2 HP, approximately 5CFM at 100 PSI. An airline Pressure 

Regulator set at 90-95 PSI should control line pressure.  Air Compressor must have a 
Condensate Drain at bottom of Accumulator Tank.  Drain every 24 hours or after 
every day’s use.  

DO NOT USE OIL LUBRICATOR WITH THE 

PORTAMATIC.

 

 

 

 

!"

There should be an Air-Line Filter between the Pressure Regulator and the Air 
Compressor.  Filter on Air-Line must be drained after use every day. 

 

Hose

 - 100’ –  3/8” I.D.   

Fitting

 -   3/8” NPT 

USE OF THE Porta-Nail 

 

The Porta-Nail is 2” long and the PORTAMATIC® with the standard shoe drives the nail into the tongue and 

groove flooring at a 45-degree angle.  The orientation of the nail is as depicted in wood floor joist construction. 

 

Summary of Contents for Portamatic




















Reviews: