background image

[email protected]

11

7077-801F  •  08/20 

H. Fire Characteristics

The overall height of the flame will vary throughout the burn 

for a couple of reasons. First is that the flame will vary based 

on type of fuel or even batch of fuel. Secondly, the appliance 

adjusts  the  burn  rate  according  to  the  how  far  away  the 

room temperature is from the set temperature. This should 

not cause alarm. The third characteristic that affects the fire 

relates to general maintenance and cleaning. Infrequent or 

poor general maintenance will result is poorer performance. 

Indicators of the need for additional maintenance activities 

include  a  lazy  flame,  black  sooted  glass,  pellets  not 

igniting, or pellets falling to the side of the firepot. See the 

maintenance section for additional information.

I. Ignition Cycles

1.  At the beginning of each ignition cycle, it is normal to see 

some smoke in the firebox. The smoke will stop once the 

fire starts.

2.  The  convection  blower  will  automatically  turn  on  after 

your  appliance  has  been  burning  for  approximately 

10 minutes.

3.  This blower transfers heat from your appliance into the 

room,  and  will  continue  to  run  even  after  the  unit  has 

shutdown. It will turn off after the exhaust temperature 

has cooled.

4.  Occasionally the appliance may run out of fuel and shut 

itself down. When this happens the empty hopper alarm 

will be triggered.

J. Running in Minimum or Maximum

When  the  dial  control  is  set  to  run  on  the  minimum  or 

maximum setting, the appliance will continue to run without 

regard to the actual temperature in the room. The appliance 

will shut off only if the dial control is set to a different setting 

or there is an error such as an empty hopper.

When running on minimum or maximum it is important to 

follow  the  daily  cleaning  activities  especially  cleaning  the 

firepot.  Failure  to  do  so  will  reduce  the  performance  of 

the appliance.

K. Running in the Automatic Mode

When the dial control is set to run in the automatic mode the 

unit will adjust the actual burn rate based on the difference 

between  the  room  temperature  as  sensed  by  the  probe 

located in the rear of the unit and the desired comfort level 

as set on the dial control.

The comfort level range is from 65 degrees Fahrenheit to 82 

degrees Fahrenheit.

Once the desired comfort level is achieved the appliance will 

automatically shut down and turn off. When the temperature 

in  the  room  drops  3  degrees  below  the  desired  comfort 

level, the appliance will automatically restart.

M. Clear Space

NOTICE:

  Clearances  may  only  be  reduced  by  means 

approved by the regulatory authority having jurisdiction.

Mantel:

  Avoid  placing  candles  and  other  heat-sensitive 

objects on mantel or hearth. Heat may damage these objects.

L. Trim Adjustment

Trim  adjustment  is  the  small  dial  located  below  the  main 

dial control. Rotating this dial will adjust the air/fuel ratio and 

below are examples of when to use it:

• 

If  the  fire  is  too  large,  lazy  or  producing  black  soot, 

rotate the dial counterclockwise one level at a time and 

allow 15 minutes for stabilization before making another 

adjustment

• 

If your fire is too small and sometimes goes out when 

there are pellets in the hopper, rotate the dial clockwise 

one level at a time and allow 15 minutes for stabilization 

before making another adjustment.

Odors,  vapors,  and  smoke  released  during 

initial operation.

• 

Curing of high temperature paint.

• 

Open windows for air circulation.

Odors may be irritating to sensitive individuals.

CAUTION

!

RISK OF FIRE!

Do NOT place combustible objects in front or to the sides 

of the appliance. High temperatures may ignite clothing, 

furniture or draperies.

WARNING

!

RISK OF FIRE!

Keep  combustible  materials,  gasoline  and  other 

flammable vapors and liquids clear of appliance.

• 

Do  NOT  store  flammable  materials  in  the 

appliance’s vicinity.

• 

Do NOT use gasoline, lantern fuel, kerosene, charcoal 

lighter fluid or similar liquids to start or “freshen up” a 

fire in this heater.

Keep all such liquids well away from the heater while it is 

in use as combustible materials may ignite.

WARNING

!

Summary of Contents for PH35PS-B













































Reviews: