Playworld Systems XX0187 Installation Instructions Manual Download Page 1

Installation Instructions

ZZUNWHOH

 

PA-833,  PA1028

Page 1 of 2

SUPERVISION INSTRUCTIONS

PLAYWORLD SYSTEMS

®

 

OVERHEAD COMPONENTS 

(SEE COMPONENT LISTING BELOW)

The Overhead Components are designed for hand over hand movement across 
the top rungs to foster play activity which combines upper body development, 
body control, hand eye coordination, and gripping ability.

Improper play and behavior on the Overhead Component can result in serious 
accidents.  The following rules for the use of the component must be applied to 
reduce the possibility of debilitating injuries:

•  Properly trained adult supervision is required at all times.  The components are designed 

to accommodate children 5 through 12 years of age.  Supervisors and parents should 
be aware of appropriate age and physical capabilities of the users. 

•  Do not crawl on, sit on, stand on or jump off the top of the assembly.

•  Users  must  move  in  same  direction  across  the  length  of  the  top  of  the  component 

assembly.  Always use fi ngers and thumbs for "Lock Grip" on hand rungs.  Do not begin 
movement across the top hand rungs from opposite ends of the structure.

•  Adequate distance, such as half the length of the ladder, must be maintained between 

users proceeding across the hand rung assembly.

•  Be  alert  to  swinging  feet  generated  by  body  movement  of  participants  using  the 

apparatus.

•  Do not use when hand rungs are wet as gripping capability is impaired.  Use only when 

rungs are dry.

•  Avoid speed contests or trying to cover too large a distance in one move.

•  Drop from hand rungs with knees slightly bent and land on both feet.

•  Protective surfacing material must be installed and maintained within the use zone of 

the Overhead Component in accordance with ASTM specifi cation F1292 appropriate 
for the fall height of the Overhead Component .

•  Review and familiarize warning document supplied with each Overhead Component 

shipment outlining owner's responsibilities on provided and maintaining required impact 
absorbing surfacing material.

As  the  owner  of  this  playground  equipment,  you  are  responsible  for 
communicating proper usage to those who may play on it.
Playworld Systems accepts NO responsibility for improper use.

Overhead Components include:

•  Horizontal Ladders
•  Horizontal Hand Over Hand Ladders
•  Horizontal Loop Rung Ladders
•  Under Catwalk Hand Over Hand
•  Under Catwalk Loop Rung Ladder
•  Sky Link
•  Sky Arch
•  Unity Overhead Canopy

 

Model ZZUNWHOH

 

PA-833,  PA1028

WARNING

!

Attention: Owner

Summary of Contents for XX0187

















Reviews: