manualshive.com logo in svg

PlayMechanix Terminator Salvation Super Deluxe, Setup And Operation Service Manual

Share
Download
PlayMechanix Terminator Salvation Super Deluxe Setup And Operation Service Manual Download Page 17

Service Manual

Setup and Assembly

Open Gun Pedestal Coin Door

1. Remove the coin door key from the coin return chute.
2. Open gun pedestal coin door.  Note the position of the Service Button Panel.
3. Locate the keys for the projector access door and lower access door on the inside of the coin 

door. Remove the projector remote control from the cash box.

Connect Floor Support Cables to Gun Pedestal

1. Position gun pedestal near floor supports.
2. Remove gun pedestal lower door.
3. Connect the 2-pin 5V IR cables from the left floor support to its mate inside the gun pedestal.
4. Connect the 2-pin AC plug from the left floor support to its mate inside the gun pedestal.
5. Connect power cable from right floor support to gun pedestal power outlet.

Attach Outrigger Braces to Outriggers

USES HARDWARE KIT ATTACHED TO OUTRIGGER

1. Position outrigger to near gun pedestal.
2. Connect lower outrigger brace to outrigger using two 

 

 torx screws.  Do not tighten.

3. Connect upper outrigger brace to outrigger using four

 

 torx screws.  Do not tigthen.

Be sure to match the angle of lower brace.

4. Verify outrigger braces line up correctly to gun pedestal.
5. Tighten down screws.
6. Repeat steps 1-5 for second outrigger.

Connect Outrigger Cables

1. Remove six screws from rear door of outrigger.
2. Remove outrigger rear door and set aside.
3. Locate outrigger power cables inside gun pedestal.  

There are 5 connectors needed for each outrigger.

4. Thread cables from gun pedestal through upper outrigger brace into outrigger.
5. Connect the three 2-pin connectors and two three pin-connectors. 
6. Repeat steps 1-5 for second outrigger.

Terminator Salvation™ Copyright © 2010 T Asset Acquisition Company, LLC

Page 17

Summary of Contents for Terminator Salvation Super Deluxe

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands